Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
just moved.range oven had only 1 wire oven rack
I just ordered a new wire oven rack from you. When it came all I had to do was to remove it from the carton it came in and place it in the oven. It fit perfectly. Thanks
Removed screws holding rear cover, removed cover. Male connector on Broil Element had rusted off and caused wire to fall onto the frame of the range, shorting it out.
Removed element by disconnecting other wire and removing the single Phillips head screw accessible from inside the oven. Released the element from the two hooks towards the front of the oven near the door and removed.
The wire to the element that burned off had a high temperature female push on connector that I did not have on hand. I had a high temp ring connector so I drilled one of the male connectors on the new element so I could use a small stainless screw and nut which I had to hold the ring terminal on.
After crimping the new connector on I fastened it to the element, connected the other wire and put the rear cover back.
took out screws on door side. Took out screws that held handle. Inserted glass and put handle back in and then put screws on side back in. There could have been better instructions with glass
Removed old assembly, attached wires to new and inserted into space for same. Of course you must turn off the range circuit breaker. The part that took the most time was removing the old assembly. Once that was done, the rest took only a few minutes.
Very easy fix. This is done through the oven door. Don't pull it out or do anything exotic. Turn the breaker off. Don't skip this Since you're dealing with 220v here. Shine a bright light into the back of the oven to identify the element attachment screws. Use a number 2 Phillips to remove the 2 screws holding the element in place. Pull the element straight out. This may require a bit of manipulation wiggling back an forth. Don't yank to hard. There was probably 6" of free wire. Next free the wires attached via spade terminals from the old element. Putt the new element in place and reattach the wires. Carefully push wires back thru the holes and secure with the screws. Reset the breaker and turn it on. Totally simple. My oven was 18 years old and the screws came right out. I expected difficulty but none encountered.
Oven element sparkled and smoked a lot and then would not heat
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Plug the wires onto the new bake element and re-screw back into place.
It was simple. I flipped the circuit breaker just in case, and then unscrewed the bracket for the old heatng element. Disconnected the two plugs, connected the plugs for the new element, and screwed the new bracket back in. The saleslady assured me when I was purchasing it from PartSelect that it was pretty easy. That gave me the confidence, and she was telling the truth. I will purchase again from Part Select....although I hope I won't have to do so for a while.
After receiving the part I was able to quickly remove the old piece and replace with the new. For this project you have to remove the back of the oven to remove the electrical attachments.
First, I unplugged the power cord from the receptacle. I then removed two philiphead screws that hold the element in place. I the pulled the element out about an inch and a half . I then disconnected the the two wires from the element. The I connected the replacement element and resecured it with the two mounting screws. I assured everything was correct and then I plugged in the power cord and turned the oven on low heat to give it a test. Everything workout just great. The part was just what I needed.
Removed two screws securing heating element. Removed broken element and disconnected wires. Removed back panel of oven, unplugged from outlet, installed new element, attaching 2 screws. From back side of oven reattached 2 wires, replaced back panel and plugged in. Pretty simple!
had to slide the range out from the wall and pull the electrical plug, then using a nut driver ,I removed 9 screws from the back panel and removed the back panel to expose the bake element wiring, had to remove the three wires connecting the power cord to the range terminals a/c the back panel would not fully come off with these wires connected. i then pulled the 2 stake eyes from the element, unscrewed the 2 screws securing the bake element from inside the stove and removed the element, re-installed the new element and screwed into place, attached the stake eyes on the rear of the element and re-attached the power cord, put the back cover back on and plugged the range in., tested and the range functioned as intended.
removed 2 screws holding top in place witch gave me ac access to none working part. removed 5 screws witch let me remove part, reversed order to reinstall part, very easy Donald Carpenter
