Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Very simple process of just ensuring you have the correct size racks and remove the old racks and replace them with the new ones. Having ordered a lot of things on the internet, I am very pleased with using Part select and would "highly" recommend them to all!!
the oven would not heat. The ignitor would heat up, but not enough to allow the gas valve to open.
The repair was fairly straightforward. The drawer below the oven had to be pulled out and the panel in the rear (looking from the front through the opening where the drawer was) was removed. It was then a matter of removing two screws and unsnapping the wire connection. And then replacing the igniter.
Racks would fall off of the tracks when the broiler was used
I ordered new racks to see if they weere out of alignment. The new racks fell from its tracks after the broiler was heated. It seems the oven cabinet is expanding with the heat and the rack width does not compensate for that. The new racks did not solve the problem so I do not know what can be done next. Any shelf support would have to be heat resistent. Replacing the oven cabinet is not a good option and no gauantee it wouldn't continue with this stove.
I pulled the racks out of the oven. Then pull the plate off that covers the burner. There is another shield with a nut on it that covers the burner. Removed it. The ignitor is mounted on the back of the burner, held by 3 screws, remove them. Pull the bottom sliding drawer out completely. (you have to lay down for this). There is a metal plate in the very back held with 2 screws, remove them and pull the plate out. You'll see the 2 high temp wires (White) with a plug connector, simply unplug the connector and you are ready to pull the whole ignitor assembly off the burner. The ignitor ceramic base simply slides out of the sleeve. Put the new ignitor in the sleeve and put everything back together. It's pretty simple. This is the second ignitor I have installed in 2 years, hopefully I'll get more life out of this one. Good Luck.
Removed oven racks and bottom cover plate. Removed stainless steel diffuser to access igniter. Removed bottom storage drawer and unplugged connector for igniter. Removed defective igniter by by taking out 3 screws holding stainless steel mounting bracket in place. New replacement part had totally different bracket which prevented it from mounting in the proper orientation so I carefully removed defective igniter from original bracket and installed new igniter. New part was tacked in place by some sort of high temp adhesive that had to be carefully removed to allow it to be installed in old mounting bracket. Installed new assembly in the oven and when I tried plugging in the power connector I discovered the pins on the new igniter were the wrong sex; both sides had male pins! Removed igniter again and cut off the two pin connector and installed a brand new 2 pin molex type connector. I installed a mating connector on the original length of wire and connector that I cut from the defective igniter along with the heavy insulating material so I now had a properly mating set of connectors. Went through the mounting process again; successful mating this time. Oven lights in 50 seconds. If it dies again I'll have a connector of each sex ready before repair.
ignitor changed resistance so gas valve wouldn't operate
The first one came damaged and customer service credited the first one and got another on the way the same day. They were awesome to deal with. I removed the oven racks, the burner cover, the storage drawr, and the door. That took about 5 minutes. I removed 3 screws that held the ignitor in place. I removed the 2 wire nuts from the wires in the drawr space. I slid the ingitor cover off the old ignitor and onto the new one. Slid the new ignitor into place and fed the wires below and put on the 2 wire nuts, then installed the 3 screws and tested the operation. I put the oven back together and put the tools away. Total time about 20 minutes.
Something got pushed into the control panel and the end cap cracked at the screw locations.
First I removed the three screws, then removed the old end cap, cleaned the area, and reinstalled the new end cap, then attached with the three screws.
thermostat knob was stripped , so i order another one , and shipping was really really fast , installation was really easy and it works great so glad i ordered the part and did it myself , i thought i to call the dealer but i did it myself
The bake of the oven would sometimes ignite and sometimes not
I pulled the ckt breaker, removed the oven drawer and disconnected the igniter. I opened the oven door and unscrewed the igniter holding bracket and removed the bracket and igniter. I broke the old igniter element when removing it from the bracket. When installing the new igniter in the holding bracket I broke the ceramic element. REALLY BE CAREFUL. Ordered a new igniter, very carefully installed it in the bracket, then rversed the removal process. It's not hard, you just have to be careful
Missing An Oven Rack Due To Plastic Fire In Our Oven. Plastic Melted Onto The Rack...Instead Of Taking The Time To Melt The Rest Off, My Husband Threw It Away =(