Models > ARG7300W (P1141296N W) > Instructions

ARG7300W (P1141296N W) Amana Range - Instructions

All installation instructions for ARG7300W parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the ARG7300W
61-75 of 186
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

oven very slow to light

  • Customer: Larry from Circleville OH
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
First I had to take the drawer completely out of the stove to reach the igniter. I then removed the screws that held the igniter in place and removed it. I had to slightly modify the replacement part by squeezing it together to make it fit into the same space. I put the replacement igniter in place and screwed it down; put the drawer back in the stove and turned on the over to see if it would light. Bingo, job done!

Oven wouldn't heat

  • Customer: Timothy from Madison AL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench(Adjustable)
  • 1 of 1 people found this instruction helpful
WEB research indicated that even though ignitor would glow, that it was likely faulty.
Turned off power at circuit breaker
Remove shelves and bottom plate from inside oven.
Unscrew deflector plate
Remove drawer under stove
Remove ignitor and unplug from connector
replace ignitor, plug in, reassemble stove.
Needed flashlight to see under stove.

Gas oven would not light

  • Customer: Elizabeth from Vernon CT
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
I have an older model gas oven which required that all screws had to be removed. With a screw gun the job would not haven taken long. Once the bottom pan was removed the oven ignitor took some finese to remove. This was only due to the short wires. Once pulled sufficiently to be able to disconnect the ignitior (although I was afraid I was going to pull the wires and separate them from the stove), it was very simple to unplug and plug in the new one (again, making sure to hold the plug so the wires would not retract back behind the wall which would have required the stove to be pulled out from the wall and the back disassembled).

The good news, it was a success and the oven works like new. Roughly $38.00 later, I am back cooking. The extra effort for the screws was offset by being able to complete this by myself and saving the cost of a repair man. Would do it again.

oven died

  • Customer: Ben from Lawrenceville GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set, Wrench set
  • 1 of 1 people found this instruction helpful
looked at and saw that ignitor was cracked,saw simple repair ahead. just needed the right part . Without part , select simple ,and easy selection, i might not have ever found the right part. as i said before finding the right part is 90 percent of the job and they made that an easy task .

of course if you want me to describe in detail, took out the pan saw the bad ignitor, removed 2 serews, disconnected 2 wire, the reassembled in the opposite direction. 30 minutes tops. I am sure this saved me at least 150 bucks for some "so called reparman" to do the same job, Most people do not realise that they have more education than most of these "repairmen". The only advantage these "repair people" have is acess to schematics and part numbers. Part select is a good start on putting this information in the hands of us average "idiots" as I am sure the repair folks call us when we pay 200 bucks for a 30 dollar job.

Gas oven would not heat up

  • Customer: John from Blairsville GA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 1 people found this instruction helpful
My repairman told me it was probably the ignitor (even though the old one sitll glowed), but after weeks of waiting for his back-ordered part, I decided to try it myself - found it on PartSelect and had it 3 days later. Turned off the power to the oven. Slid out the 2 racks, and the cover below the racks. Unscrewed 1 nut and removed the V shaped metal plate that distributes the heat. Under that removed 3 screws that hold the ignitor clip in place and got the igniter out of the clip. I couldn't get to the plug on the other end of the ignitor until I took out the oven drawer and removed 2 screws holding a metal cover in place below the oven. Reversed the whole process being careful with the end of the new ignitor (I read it was fragile). The oven now heats up in 5 minutes and maintains temperature again!

Oven would not light, broiler would

  • Customer: james from lancaster NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 1 people found this instruction helpful
Remove the cover over the burner, two screws at the rear, this exposes the burner tube cover, one nut at the center. Three screws will remove the holder for the igniter. I had to remove a sheet metal cover underneath the oven( pull the drawer out) to gain access to the plug for the igniter. A good tip on this is the same valve controls the broiler and the oven, if one works and the other doesn't, it's the igniter. If neither works the gas vale may be the problem.

The Oven would not turn on reliably

  • Customer: Carlos from Grand Rapids MI
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 1 people found this instruction helpful
Remove the racks
remove one nut that holds the heat deflector
3 screws that hold the igniter
remove the drawer
remove 2 screws holding a heat shield in place.
unplug old igniter and reinstall

Oven would not light, even though the ignitor looked as though it was working, the slightest crack affects the resistence and the signal to send gas does not work.

  • Customer: WILLIAM from BENSALEM PA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 1 of 1 people found this instruction helpful
It was Tuesday before thanksgiving, panic as there was a big bird looking for a hot stove,
unplug stove from its electrical supply
turn off gas, not necessary but sometimes it's good to be safe.
inside oven remove bottom splash cover "pull towards you and lift out, then remove flame pan, one nut in the center, remove and lift out flame pan.
The oven ignitor was to the left of the burner, with 3 philips screws one attached to buner and the other two to the back of the stove, remove all three.
The ignitor is now loose,
remove bottom drawer and behind is a plate attched to the back of the stove with two screw, the screws are facing you as you look in where the drawer was, remove screws and plate to access the plug attatching the ignitor to its power supply .
go back to the oven and remove ignitor.
install new, feed plug through back, and put it all back together.
"ignitor very delicate, handle with care"
I am also not the biggest of guys and it can be awkward getting in the drawer space as you need both hands to plug it back in, so tilting the stove back, keeping safety in your thoughts at all times, would be a must for most people.

ignitor changed resistance so gas valve wouldn't operate

  • Customer: Trevor from Silverthorne CO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
The first one came damaged and customer service credited the first one and got another on the way the same day. They were awesome to deal with. I removed the oven racks, the burner cover, the storage drawr, and the door. That took about 5 minutes. I removed 3 screws that held the ignitor in place. I removed the 2 wire nuts from the wires in the drawr space. I slid the ingitor cover off the old ignitor and onto the new one. Slid the new ignitor into place and fed the wires below and put on the 2 wire nuts, then installed the 3 screws and tested the operation. I put the oven back together and put the tools away. Total time about 20 minutes.

Range top worked; broiler worked; oven would not heat.

  • Customer: Philip from W. Bridgewater MA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 1 of 1 people found this instruction helpful
Disconect power source; Remove oven racks, remove storage drawer under oven; remove floor of oven, remove flame deflector, remove three screws holding igniter cage and unplug faulty igniter. Reverse all steps for reassembly.

Oven either would not come to set temperature or took a very long time. Gas would flow to burner for only short times. When burner was lit, flame was often low. There was often the smell of gas.

  • Customer: Richard from Chicago IL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
Symptoms were sign of bad ignitor based on Goggle searches. Removed screws holding burner and ignitor to range. Disconnected ignitor at green connector below oven with lower drawer removed. Then removed burner and old ignitor. Reinstalled burner and then new ignitor being sure burner was still seated on gas outlet. (Note-burner removal may not be necessary) Replaced two screws attaching ignitor to oven wall and two screws attaching burner to floor of oven. Oven works perfectly now.

After on-line research i realized the igniter failed.

  • Customer: James from Davis CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
Replacing the igniter itself was a simple matter a few screws holding its housing and then plugging the new one into the connector. Difficulty came trying to figure out how to access the igniter. Disassembling the floor of the oven was a dead end involving many screws. Pulling the unit out from the wall was a big job and another failure. The problem was solved with the removal of the drawer. Underneath, in the rear was a sheet metal plate held by 2 screws. Behind that hung the igniter connection. Voila! Job done.

Something got pushed into the control panel and the end cap cracked at the screw locations.

  • Customer: Michael from Baltimore MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
First I removed the three screws, then removed the old end cap, cleaned the area, and reinstalled the new end cap, then attached with the three screws.

The oven would take 45 minutes to over an hour to preheat.

  • Customer: Timothy from Elk Grove Village IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
I removed the oven door by removing two screws, one above each hinge. With the door screws removed, position the door to the slightly open position and lift strength up to remove. Remove wire racks and the cover from the bottom of the oven. Remove the heat deflector which is held on with a single nut. Remove the screws that hold the cavity that houses the igniter and the burner. The igniter is held in place by a protective bracket that has to be reused. I slid the old igniter out of the protective bracket and then removed the cavity by allowing the burner and igniter to exit through an opening in the rear of the cavity. The drawer (broiler pan storage) had to be removed to remove the two screws to an access panel that allowed access to the igniter connector. After disconnecting the old igniter, I fished the new igniter connector through the back of the oven to connect it. I use masking tape to hold the access panel in place while reinserting and tightening the two screws. Replace the cavity that houses the igniter and burner. Slide the protective cover over the igniter. Realign and secure the burn and igniter assembly by reinserting and tightening the necessary screws. Reinserting and tighten the screws around the igniter/burner cavity. Replace the heat deflector by tightening the nut. Replace the cover that covers the bottom of the oven and the wire racks. Reinsert the drawer. Slide the door over the hinges and reinsert and tighten the two screws.

oven wouldn't turn gas on, no heat

  • Customer: Craig from jericho VT
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 1 of 2 people found this instruction helpful
Removed oven racks and bottom cover plate. Removed stainless steel diffuser to access igniter. Removed bottom storage drawer and unplugged connector for igniter. Removed defective igniter by by taking out 3 screws holding stainless steel mounting bracket in place. New replacement part had totally different bracket which prevented it from mounting in the proper orientation so I carefully removed defective igniter from original bracket and installed new igniter. New part was tacked in place by some sort of high temp adhesive that had to be carefully removed to allow it to be installed in old mounting bracket. Installed new assembly in the oven and when I tried plugging in the power connector I discovered the pins on the new igniter were the wrong sex; both sides had male pins! Removed igniter again and cut off the two pin connector and installed a brand new 2 pin molex type connector. I installed a mating connector on the original length of wire and connector that I cut from the defective igniter along with the heavy insulating material so I now had a properly mating set of connectors. Went through the mounting process again; successful mating this time. Oven lights in 50 seconds. If it dies again I'll have a connector of each
sex ready before repair.
All Instructions for the ARG7300W
61-75 of 186