ARB9059CS (PARB9059CS0) Amana Refrigerator - Instructions

(1) Watched the PartSelect installation video. (2) Placed Order. Arrived in two days, regular delivery. (3) Opened package. (4) Selected installation tool. (5)Removed old Ice Maker Assemply (6) Replaced w/new. Ice in a couple of hours. Video & order/delivery aside, the entire process took less than 10 minutes including selecting tool and opening package. PartSelect video very helpful.

No instructions with part. Found a picture on line and changed the arm, but it didn't fix the problem. Fairly easy after figured out what needed to be done to get to the part.

I replace the defrost timer and the defrost thermostat. It has been a week and is working fine. I almost did not order the defrost thermostat when I checked the coils I noticed that water had gotten inside the t-stat and it was damage from freezing. Glad I ordered both parts.

After watching the video witch was GREAT help THANK YOU

Read articles online from other sites. Other sites stated part was behind unit and to replace it on top of the compressor. Wrong. Part was behind freezer section on this model. Removed 4 screws from freezer to find out I also needed to thraw all the ice from behind plate in freezer. This took the longest time approx time 1/2 hour to do this. After that the part was easy to install. If I knew the part was behind the freezer plate the total time would have been around an hour to do. Please remember to pull the plug before you start cutting wires to replace the thermostat kit. It has now been running for about a week and no problems at this time with refrigerator

The Amana's Ice Maker mounted against the back wall. I'm a 61 year old female that ordered this to help my aging parents. The wire harness only unplugged from the Ice Maker and was hard wired to the Frig. I had to "blindly" try to depress and release the harness clip and that took most of the time. When putting in the new ice maker, I noticed that the opening for the fill tube was now against the wall and not to the back. So, I had to disconnect it again. I found that it is also made for a side right fill by cutting out a perforated tab. Just to make sure there wasn't an overflow out of the other round hole, I used silver tape to plug the hole. It took two hours after plugging back in the frig and turning on the water supply before it made ice.

Kids complaint no ice and smelled like burned plastic,found ice maker melted,Replaced ice maker assembly,used existing harness not supplied with new unit,ice maker still no ice,verified an open at fuse link,installed inline fuse in place of existing fuse link.I was told harness not available.Harness section should be on new unit.Hint Hint!

Ordered replacement icemaker from PartSelect.com. Upon receipt of part installed part as per the online video. All went well. Whirlpool rep. stated that the icemake works well when the freezer temp. is set at 10 degrees or less.It took appreximately 24 hrs.for the icemaker to fill the bucket with fresh ice. It would hace cost approximately $230.00 or more if I had called a Service rep. to do the job. So I elected to do it myself.

well, my problem was the dual water valve. I check the two water valve connectors, one was good ( yellow ) and the other connector (brown) was bad. I tested them both with an ohms meter, of course all power was off. I think when ever there's a problem with not receiving ICE this should be done before replacing the ice-maker for there's a lot of things going on in this area. The Brown Connector releases the water into the ice-tray (that tested Bad with a reading of 257 from ohms meter,and the yellow had a sound from ohms for full contact a good reading. The brown valve was bad.

Followed on line instructions. Instructions were very helpful. The part was an exact replacement. Everything went as planned.

Removed the ice maker and back interior panel of freezer. Located the defective defrost thermostat that was clipped onto the coil. Simply unscrewed the two wire nuts and removed defective thermostat, it was obvious as it had a bulge in it. Clipped the new defrost thermstat on, wired it via the two wire nuts. Put everything back together and freezer is back to normal. Very easy repair.

Followed the Video, and it went almost as the video, except for the rails for the ice tub, so instead of the nut driver, had to use an open end 1/4" wrench. Now its a working with lots a ice....

I received the new icemaker the next day after I had ordered it. After watching the video on how to install the icemaker I installed it within a few minutes which I really surprised myself since this was my first repair job to do by myself. The new ice maker has been working great and I am very pleased with partselect and will continue to contact you when I am in need of any parts. Thank you, betty

1 removed ice basket 2 remove cover over basket 3 unplug power cord 4 loosen top screws with 1/4 in nut driver (do not remove the completely) 5 remove lower mounting screw ( not necessary to remove basket rail) 6 remove ice maker from unit 7 remove bale from old unit 8 install bale on new unit 9 remove front cover from old unit 10 remove power cord from old unit 11 plug in cord to new unit 12 install old front cover on new unit 13 mount unit in freezer 14 hang unit on top screws 15 install bottom screw 16 plug in unit 17 put in ice basket and cover. no runs, no drips, no errors. Ice was made in about 2 hours.

Fast delivery...Great video instructions..The only difficulty is when I tried to take the cable out. It's kind of hard and far away from my reach. So, I took only the cable out on Ice Maker end.