Models > ARB9059CS (PARB9059CS0) > Instructions

ARB9059CS (PARB9059CS0) Amana Refrigerator - Instructions

All installation instructions for ARB9059CS parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the ARB9059CS
616-630 of 677
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

wheel broke

  • Customer: kenneth e. from phx. AZ
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
GRIND RIVET HEAD OFF , INSTALL RIVET TAP END

Crisper frame replaced

  • Customer: Glenn from Seattle WA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I order a bare crisper frame, no glass, no slider controls. The old frame lifted out easily. I did not realize the glass top is not glued in, because food drippings had it somewhat stuck in place. But only somewhat - I almost dropped the glass when I turned the frame over. Once the glass was out, I removed the humidity sliders by gently lifting one end so I could slide them to a place where they lifted off. (Look for the notch-outs.) Then I put the parts in the new frame and put it back in the frig.

Replace Ice Maker

  • Customer: Terri from Manhattan Beach CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
The fix was relatively easy but I could not get 2 of the screws removed. They were in very tight and I didn't have the right tools. Also, in the Amana refridgerator, they are in a "difficult to get at" location. I called my plumber friend and he helped me. Once the screws were out, the rest of the job went very smoothly as others have described. We took out the bad icemaker and reconnected the new one to the existing harness. I had ice in an about an hour. Thanks so much, PartSelect. The delivery was quick and the install was as many described on your website. You provide a wonderful service for the "do it yourselfer". Terri

The ice tub corroded so the ice would stick.

  • Customer: Hal from Marathon FL
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Couldn't believe how complicated this part is with heaters. It is used in at least a billion refrigerators and functions well. But I had to tear it all apart to adopt it. Got it all done and stayed awake all night for waiting for Ice. Nothing! Then a Erika moment! Turn the ice arm full switch off! Then Ice poured out every hour. Expecting many years of ice. Thanks for speedy delivery especially before Christmas..

new prob. ice dispencer door seal leaks

  • Customer: vern from lake placid FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
need instr. to repair

Replace crisper drawer

  • Customer: Kathleen from Boulder CO
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
The replacement itself was as easy as it gets. What made it harder was the need to remove the white plastic cover from the old drawer. Although some said it was easy, ours was a bit of a challenge. The video was helpful, in letting us know to start at the bottom when removing the cover. After that, pretty easy. No tools required.

Did not self-defrost

  • Customer: Dan from Wellesley MA
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Remove freezer door: two pan head machine screws on sides of track, lift and pull. Remove icemaker: electrical connector with latches, three sheet metal screws with 5/16 hex heads, easiest to get top two first. Remove bezel vent from back panel: 3 latches, one lower center other two upper sides. These release with a 3/16 screwdriver. Start with the center one. Remove back panel: 4 sheet metal screws in corners, bow outward to clear retainer and pull out. May have to defrost coil and fins: remove any loose frost gently with plastic scraper, warm with hot air gun on low setting, keeping it moving and a foot or so away from refrigerator parts. Mop up water. Diagnosis: set multimeter to read resistance. Unplug orange wire connected to thermostat. One probe on orange wire, one probe on brown wire, where it enters the multi-connector. Unclip thermostat and warm in your hand. Should be open circuit. Bury thermostat in a handful of frost to cool down. Should be closed circuit. I had about 6 M Ohms, so decided problem was probably thermostat. Also checked heater, which had 30 Ohm resistance, which is correct. Reassembled, ordered part. Disassembled. Unclipped old thermostat and cut off wires. Kit comes with end cap electrical crimps. I used butt splice crimps instead, with a bit of heat shrink tubing over the ends to keep water out. Unplugging orange wire made this a bit easier. Clipped thermostat back onto coil. Reassembly: snap in back panel, re-attach screws. Make sure icemaker hose and connector pass through respective holes, and connector is latched in place. Watch out for sharp edges. Re-install bezel grille; alignment is a bit finicky. Re-install icemaker. Re-install door and baskets. Store food. Done.

Ice maker was dripping water in two different area's

  • Customer: Michael from Maplewood MN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
The repair was a lot easier than I thought. I first ordered the ice-maker part from PartSelect. Followed the instructions from the how-to video and I was done within 30 minutes. Unplugged the fridge, took out the two 1/4" nut screws holding up the ice-maker, disconnected the wiring harness and then re-attached the new ice-maker in reverse order. Had to use some of the parts from the old ice-maker, like the cover, ice wire (the wire that moves up and down, letting you know when the ice box was full or starts the ice-making process) The whole process along the PartSelect video made it easy.

light would come on and off

  • Customer: Dora from Rock Island IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Viewed the viedo - it showed what to do

follow the video that PartSelect has online

  • Customer: Rich from Wickenburg AZ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Watch the video and then do the repair.

Bulb replacement

  • Customer: Judith from Phoenix AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I pulled down the wire around the glass cover...released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

Ice maker not making ice

  • Customer: JOHN from SAINT PETERS MO
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
First of all, I do not consider myself very handy. Most of my simple home repair projects include at least 2 trips to the local hardware store and take twice as long as they probably should. So if I can do this anyone can. For once, rather than just blindly throw new parts at a problem I did check the water pressure to the icemaker first and then even tested the icemaker with a multi-tester to determine what was wrong. I had $5.00 mulit-tester in my workbench but had never actually used it before, so I found step by step instructions on another website on how to test the motor and it turned out that one of the circuits in the main motor was in fact bad. Since the motor was around $80.00 dollars and the Whole unit that's inside your freezer is about $120.00 I decided it was best to just go ahead and replace the entire unit rather than just the motor. From what I saw online normally replacing an Ice maker is fairly simple. Remove 3 screws swap the prewired plug along with the metal arm then just reinstall it. Somehow whenever I try a home repair it's never that simple. First of all, our freezer is on the bottom so removing the screws holding the ice maker meant that I had to climb over, around and under the freezer shelves in order to get to the ice maker itself. Also one of the screws is not visible from the front so I had to hold a mirror in one hand while I tried loosening the screw with the other. Since the metal arm that turns off the ice maker is not included in the replacement it had to be moved over. Of course it was stuck, so it did take a little time to get it loose because I was being careful not to bend it and have to order another one. Finally installing the new icemaker meant once again that i was climbing over under and around the basket in the bottom level freezer. There is probably an easy way to remove the entire drawer but I couldn't find the release tabs so when just pulling harder on the drawer didn't work, I thought it best to just work around it. Still all in all, not a difficult job, just a little time consuming. The guy in the video did the swap in about 6 minutes, it took me about 45.

The ice maker was leaking into the holding container and had black chips of paint or plastic from the inside of the icemaker

  • Customer: Gerald from Waukesha WI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Installation was really easy since the replacement part was identical to the OEM part. Removed the three mounting screws with a nut driver. This allows one to remove the icemaker from the wall and disconnect the wire harness plug from the icemaker. I never unplugged the harness from the rear wall of the refrigerator. Put the new icemaker in place, making sure to place the water fill tube in the proper hole. Plugged the wire harness into the new icemaker and tightened the three mounting screws. The icemaker worked perfectly from then on with clean ice cubes and no leaks.

Left door light switch lost its spring

  • Customer: David from Fairfax VA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Unplugged appliance. Using a small putty knife I moved the switch out far enough to grab it with pliers. Moved wiring to new switch and pushed into place after testing.

PART WHERE ICE MAKER ARM FIT IN BROKE OFF

  • Customer: Yvonne from Worthington IA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
TOOK ICE MAKER OUT ALL TOGETHER WE REMOVED 4 TO 5 SCREWS HAD TO REMOVE AXEL TO GET THE BROKEN PIECE OUT AND NEW ONE IN MY HUSBAND SAID IT WAS EASY IN AND OUT IN ABOUT 15 MINUTES SAVED ABOUT 150.00 THANKS PARTSLECT
All Instructions for the ARB9059CS
616-630 of 677