AR2T661WW-P1130980NW Amana Range - Instructions

by myself

Pulled range away from wall and unplugged it. Pulled smoothtop out a bit to clear retaining clips. Swung top up and unplugged the cable going to top. Removed top hinge so top could be removed. Put top upside down on a table to work on. Removed wires from bad burner and then removed screws holding the burner in place. Replaced bad burner with new one and reversed the previous steps. Range worked like new. PartSelect service was great, received the part in one day.

Unscrewed 2 screws holding the bracket on the back of the stove and disconnected the wires from the two clips. Removed back element, connected new elements & replaced screws to back inside wall of oven. Works like brand new!!

I went to the source of power on the stove and noticed one of the terminals had come loose from the terminal block and had shorted out against the cover of the terminal junction. After prying the loose terminal off cover I ordered new terminal block and received it the 2nd day. I removed the old terminal block and replaced the part in about 10 minutes..Thank you Parts Select for your easy to find diagrams and quick delivery.

Removed back panel, unplugged sensor, removed sensor from inside oven (2 screws), replaced with new part.

Removed top of stove replaced heating element ,piece of cake.

Discriptions provided by others in this section made it easy and there is little additional insight I can add. The part was delivered the next day. I don't reply to these requests for comments, as providing what I paid for is the expectation. But, this outfit did a good job.

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

I used a phillips screwdriver to remove the control switch. I drew a diagram on a piece paper where the wire contacts connected I wrote the different # and wire colors down . I compared the 2 switches they were the same. So I connected the wires . I put the 2 screws on. The stem was higher than the other switchers. So I had to cut the stem shorter. It had groves so it was easy to use a hacksaw to cut a little then use a lock pliers to hold the stem and another to break it off then it fit perfect I put the knob on presto new switch. Just like new.

Pulled cooktop up on Counter top and unscrewed the screws around around the cook top lifting the glass top off to get to bad burner.then disconnected wires from old burner lifting burner out and sitting new burner down in the cut outs. I have used parts select for my refrigerator,microwave and oven I can't say enough about how great there website is as well as there service.they have made a customer out of me for life and I have turned a lot of friends on to the site and they love it as we'll.

Had to screw off old terminal block & screw on new one

the burners were located underneath the glass top, but i had no instructions on how to remove the glass top, so i spent an hour taking every screw off. finally i realized the glass top lifts off from the front then the repair became super easy. hard part was replacing all the screws, lol

I had already removed the old hinges by removing the screws/bolts and removing the broken hinges from the back side through the drawer below the oven that I had already removed. Took the new hinges and screwed the two metal screws into the top hole on the new hinges after placing hinge in vise, one screw on each then removed them and placed them to the side. Determined the right tap from my tap set, and then tapped the bottom two holes on the new hinges, one on each. Placed the bolts that came with the new hinges into the holes I had just tapped, screw them in, then I removed them and placed to the side. Took hinges and bolts / screws to the oven, inserted hinges in through the drawer that I had removed up to each side where hinges would come back out to the front of the oven. Placed screws / bolts one at a time through oven door frame into the hinge on the back side, and then threaded them into the hinges and tightened. Replaced oven door onto new hinges and checked for correct operation. Door works like new.