Quick Question!

Have you ever purchased from PartSelect.com before?

Models > ALW210RAW

ALW210RAW Amana Washer - Overview

Parts and Repair Help for models starting with ALW210RAW

If you know the washer repair part you need, you can browse the list of all parts for models starting with ALW210RAW, or you can search by name or part description. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for ALW210RAW parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Models starting with ALW210RAW

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$5.15

Washer, Thrust

This washer is 3/4 inches in diameter.

$5.15

Hose Clamp

$5.10

Screw, 8/18 x 3/8

This screw is sold individually.

$5.51

Hose Clamp

This hose clamp is sold individually.

$34.79

BELT- SPIN

This v-shaped spin belt helps transfer power from the motor to the transmission to help pump the water in and out of the washer. It also helps runs the spin cycle in the washer.

$21.40

Drain Hose with Rubber Elbow

This hose attaches to the pump to help remove the water out of the washer.

$10.35

Adjustable Levelling Leg

Sold Individually. This adjustable leveling leg comes with a stop nut.

$10.11

Retaining Ring

This metal retaining ring is well under an inch long. Use it for your Maytag brand clothes washer or your clothes dryer.

$5.15

Lid Hinge Mounting Screw

Sold individually.

$21.03

Idler Pulley Wheel

This wheel has a center metallic bearing. A dryer's idler pulley wheel serves to help the belt to rotate the drum.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Belt wore out

  • Customer: Bruce from Medina, OH
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set
  • 167 of 192 people found this instruction helpful
Had to remove pump-not easy. Nothing wrong with pump, but had to trash it to get it off the motor shaft, so I had to replace it, too.

Pop up top of cabinet and remove front panel. (I leaned unit back against a wall to facilitate internal access once panel was removed.)


Remove motor assy - 4 screws & connector.

Remove ... read more

Drive Pump Leaked

  • Customer: Stephen from Laveen, AZ
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench set
  • 67 of 79 people found this instruction helpful
It took some trial and error but overall not a difficult project. 1. Take the front covers off. 2. Undo the pully spring to loosen belt 3. Remove belt off idler pulley wheel and free up belt from the large wheel. 4. Disconect the wiring harness and the hoses. 5. Undo the motor mounting bolts (4) 6. Take motor out of washer and remove the 3 screw... read more

Water leaking on floor from "mysterious place underneath washer"

  • Customer: Bryan from Chicago, IL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Socket set
  • 40 of 45 people found this instruction helpful
Water was leaking on the floor during the wash cycle and especially during draining of the washer. I removed the front panel at ground level and watched while draining after a rinse.

I t was obvious that water was spraying from a hole in the rubber end of the hose (the hose is a fused assembly of a plastic section and a rubber section).

read more