ALG643RAC Dryer - Instructions

I opened the package that arrived and inserted the new lint filter into the place where the old one was. Then I threw the old lint filter away

The video on this site for replacing the drum support roller was quite good but for my particular model of dryer was not totally applicable. The video shows that by using a putty knife to disengage two spring clips in front, the top would open but my dryer had two screws in addition to the spring clips securing the top down. Those screws were accessed after taking off the front of the dryer first. That cost a little bit of time as it was an unexpected step and I did not want to damage my dryer. If your top cover is not popping off as easily as in the video, look for two screws on each corner holding it down. Other than that variation, the rest of the repair went as shown in the video. I did not isolate the cause of the squeaking to a drum support roller, the idler pulley wheel, or the belt but I decided to change out all of them since I would have the dryer apart and the parts are not expensive. I would recommend not buying the overpriced thrust washer and retaining ring as the old ones can be reused if you have removed the ring carefully with ring clip pliers. Notes about the repair: It is easy and I was able to do it without help with the drum. Take the time to do a good vacuum while you're in there. You can get an inexpensive set of ring clip pliers from Harbor Freight. They really helped and even a set of small needle nose pliers would not have been useful. Note about Parts Select: The prices for the parts was reasonable, with the exception of the thrust washer and retaining ring. Shipping was very fast and my order was fulfilled perfectly. I will return.

The part came in very quickly. If you know how to remove the front panel, it is very easy to repair. The hard part is to diagnose the problem. The first thing to check is the igniter. If it comes on then you look for faulty limit switches. If you have lots of training in electronics and appliance repair this is very easy, if you do not I would not try this. I have 40 years in the repair business, It still took me 1hr. to find the problem. the switch was intermitted, one time the dryer would work the next time it would not. Good luck and happy repairs.

Pushed in the Door Catch, and it was fixed.

Installing the new switch was a snap. With the dryer unplugged, open the top using a putty knife to release the 2 clips - one on each side. Lift the top and support it to stay open. Next, note the wire color and location for each of the 3 wires. Remove each wire from its prong on the bad switch by gripping the connector with pliers and pulling off. Next remove the bad switch by squeezing the tabs on the sides of the switch to release it. The switch removes to the front of the dryer. Install the new switch in the same method and reconnect the wires as before making sure the colors go back on the same prongs. I had to replace one of the connectors with a larger one (that came with the switch) since one of the prongs on the new switch was larger than the orginal (bad) switch. To do this, I cut the old connector off, stripped the end of the wire, and crimpted on the new connector. I had to be careful not to waste too much wire since there was very little slack to work with.

I unplugged the dryer, pushed the clips loose and tipped the lid up and tied it open to a cabinet above. Disconnected the electrical connections to the front panel and removed front panel. Then I disconnected the electrical connections to the drum support. Removed four sheet metal screws holding the support and lifted out the support. Removed the drum glides at the bottom, installed the new drum glides with felt pads. I replaced the drum rollers just so I didn't have to do it later. Put everything back in reverse order and running quiet! Well worth the $42.57 spent for parts and postage.

Besides successfully ordering the correct part I also noticed there were instructions on the website as to it's removal process. MOST helpful, I had not predicted the difficulty in doing it until I read the instructions. Very helpful.

Unplugged dryer from power source, used putty knife to release latches that hold top on, tilted the top out of the way, unplugged door lite, located the radiant switch, removed 1 screw,then undid 2 wires & lifted out switch. Reversed procedure plugged in dryer....wa la had dried a large load of clothes, took 1/3 the time to dry clothes at last. Thanks "PartSelect"

follow video inst.

First time through it was an interesting adventure... Had to take the front completely apart... When I took the drum out that is when a roller earning had melted off... And the limit timer was broken... The second time through it went faster... And I had my son help... He is not mechanically inclined but he did well...

Remove drum assembly, replace drum roller, belt with Pulley wheel bearing. The whole problem was corrected and the unit now runs like new.

Ordered part ( door latch ) flowed instructions easily fixed same.

I removed the front panels, lint screen, ductwork to fan, motor assembly, drum, drum rollers, and vent pipe to outside. I then cleaned years of accumulated lint and dust from the cabinet. Replaced the drum rollers, drum glide, idle pulley and motor assembly. The hardest part was getting my arm in to place the idle pulley onto the drive belt.

Not quite as show on your repair intructions. But, all in all not that difficult. Things went very well. However, in the midst of the repair I found I had to replace other worn out parts.

I first unplugged the dreyer from the wall, I then used the putty knife to push clips in on top of the dreyer and opened the top. I used a nut driver to remove the front panel and unplugged the light and door switch wires. I then reached under the drum and removed the belt, and then lifted the drum out of the cabinet. I used snap ring pliers to remove the rollers and replaced.them with the new ones. After installing the new rollers I placed the new belt around the the.drum and lifted the drum by the belt placing it back into the cabinet. With the drum back in place I reattached the front panel and turned the drum to make sure it was not hanging up on the felt rings. With the drum moving freely and the belt hanging down I layed back in front of the dreyer and put the belt on the motor and reached up to.the tension pulley and placed the belt under the pulley. Once the belt had tension on it I again manually rotated the drum to make sure it wasn't binding anywhere. All was good so I replugged the light and door wires, shut the lid and plugged the dreyer back into the wall socket, turned it on and it worked great. From start to finish it took about.40 minutes and half that time was spent cleaning out the cabinet which had quite a bit of lint. I have used the.dreyer several times since the repair, and this completely took care of the problem. I highly recommend ordering the rollers along with the belt as mine were well worn and it saved me from having to take it apart twice. All in all a very eazy do it yourself project.