Models > ALG443RCW

ALG443RCW Maytag - Overview

Parts and Repair Help for models starting with ALG443RCW

If you know the repair part you need, you can browse the list of all parts for models starting with ALG443RCW, or you can search by name or part description. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your . We’ve also included any installation videos we have for ALG443RCW parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Models starting with ALG443RCW

$7.64

Drum Support Roller

This roller is for square-ported models and has a metallic bearing in its center. They are sold individually and most dryers use 2 rollers at the rear and it is recommended to repl...

$14.26

'M' Series New Style Coil Kit

This gas dryer ignition coil set comes with two ignition coils: one three terminal Boost/Hold coil, and one two terminal secondary coil.

$13.22

Multi-Rib Belt

At 93-3/8" in length, this flat dryer drum belt has 5 ridges and is 3/8" wide.

$3.91

Drum Glide

This drum glide is sold individually. ***Please Note: these should be replaced in pairs.

$4.06

Idler Pulley Wheel with Bearing

A dryer's idler pulley wheel serves to help the belt to rotate the drum.

$4.46

Thrust Washer

$31.70

Lint Filter

***Note: This part no longer comes with the felt seal. This filter collects lint as it passes through the dryer vent.

$6.19

High Limit Thermal Fuse

Meant as a backup to a high limit thermostat, this fuse is typically set to trip at a higher temperature than that of a high limit thermostat. This is a one-time use fuse, so when it does trip, you do need to replace it. It's letting you know that something is wrong with your dryer.

$25.16

Radiant Flame Sensor

This part senses the flame for heat allowing the gas valve to open.

$2.70

Retaining Ring

Sold individually.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Drum not centered , clothes getting stuck in dryer

  • Customer: Chris from Hopedale MA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 464 of 463 people found this instruction helpful
The first thing I did was to unplug the dryer from the wall. Then I removed the bottom two screws and slid the bottom cover off so i could see all the way to the back, I tipped the dryer back against the wall and searched for the problem with a flashlight. I noticed that one of the guide wheels that held the drum in place was sheared off. I took the new d... read more

The Felt Gasket between drum and door ripped, vent manifold from Dryer to fan and lint screen broken

  • Customer: Tim from South Glens Falls NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 458 of 458 people found this instruction helpful
I pulled the bottom panel and the door panel to replace the manifold and felt gasket around the drum. I removed old gasket very easily, it peeled right off. I use brake cleaning fluid (Spray Can from Auto Zone about $1.45) to remove old glue. Used spray contact cement (Elmer's about 4.50 at Ace) and sprayed the panel and gasket surfaces and let dry. I th... read more

Filter Lint was broken

  • Customer: Mirsada from Yorktown Heights NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 363 of 365 people found this instruction helpful
Took it out of the box and put it in the dryer. I could not find this part anywhere else but on this website. The item was delivered the next day to my surprise. read more