Quick Question!

Have you ever purchased from PartSelect.com before?

Models > ALG443RCW (PALG443RCW1)

ALG443RCW (PALG443RCW1) Amana Dryer - Overview

Get Parts and Repair Help for ALG443RCW

If you know the dryer repair part you need, you can browse the list of all parts on the ALG443RCW, or you can search by name or part description. You can also find your part by where it is located on the ALG443RCW by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for ALG443RCW parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$14.08

Multi Rib Belt - 93-3/8"

This dryer drum drive belt attaches to the motor pully and works the drum as the motor rotates. The belt has a length of 93- 3/6 inches, and wraps all the way around the dryer drum...

Order within the next 7 hrs and your part ships today!
$9.30

Drum Support Roller - for square ported models

This drum support roller is used for square-ported model clothes dryers. It has a metallic bearing in its center. The drum support roller holds the drum in place while it rotates on the support wheels. You may have a faulty or damaged roller if your dryer will not start or tumble, takes too long to dry clothes, or starts making loud noises. This part is sold individually; however, rollers tend to wear at the same rate, so it is suggested that both should be replaced at the same time. Customers have ranked this repair as easy and should take 15-30 minutes to complete.

Order within the next 7 hrs and your part ships today!
$7.69

Idler Pulley Wheel with Bearing

The idler pulley wheel helps the belt to rotate the drum in your dryer. If your dryer will not start, will not tumble, or is noisy during operation, the idler pulley wheel may need...

Order within the next 7 hrs and your part ships today!
$27.70

Radiant Flame Sensor

If your gas dryer is not heating up or igniting, then replacing the flame sensor, located in the burner assembly, could solve it. This part senses heat from the igniter to monitor if it is hot enough to ignite gas to light the burner. Once the igniter is hot enough it will open the valve and allow gas to flow. This is a safety mechanism to prevent dangerous levels of gas from building up. To repair, the main top of the dryer should be lifted, as well as the front panel to access the component. This flame sensor assembly is made of both plastic and metal.

Order within the next 7 hrs and your part ships today!
$35.69

Lint Filter

Note: This part no longer comes with the felt seal. This filter collects lint as it passes through the dryer vent.

$4.63

Washer, Thrust

This genuine OEM washer has a 3/4 inch outside diameter. This thrust washer can be used on most makes and models of dryers. A complete list of compatible dryers is available below. The washer is found on dryers around the drum support rollers and idler pulleys, and helps prevent the rollers and pulleys from bumping up against the brackets they are installed on. Your thrust washer could be defective if you notice your dryer wont tumble, rotate, or turn; or there is a load squealing or whining noise when the dryer tumbles. The repair is a relatively easy job. You will require a putty knife, 5/16 inch nut driver, and E-Ring pliers. Remember to disconnect the power to your dryer before you begin the repair.

Order within the next 7 hrs and your part ships today!
$14.78

Door Catch Kit

This door catch kit is designed for use in dryers. This is an authentic OEM replacement part. This catch assembly ensures the door of your appliance will close, and remain closed. ...

Order within the next 7 hrs and your part ships today!
$16.71

Door Switch Kit

This part replaces two terminal switches in a dryer and prevents the dryer from running when the door is open. This includes two connectors. If your dryer will not shut off, start, or does not tumble, replacing the door switch can solve this appliance problem. The tools needed for replacement are a screw driver and wire strippers. Make sure to attach the two wires to the right two poles of the new switch, to do this you can check the resistance of the switch. Unplug the dryer before installing this part, also refer to the diagram provided by the manufacturer.

Order within the next 7 hrs and your part ships today!
$19.12

Cylinder Felt Seal

This cylinder felt seal is used in dryers and is located between the back of the drum and the rear dryer panel. If your dryer is experiencing any of these symptoms, replacing the f...

Order within the next 7 hrs and your part ships today!
$21.88

Cylinder Glide Bracket

These brackets support each side of the tub. Order quantity needed.

Order within the next 7 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Drum not centered , clothes getting stuck in dryer

  • Customer: Chris from Hopedale, MA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 498 of 506 people found this instruction helpful
The first thing I did was to unplug the dryer from the wall. Then I removed the bottom two screws and slid the bottom cover off so i could see all the way to the back, I tipped the dryer back against the wall and searched for the problem with a flashlight. I noticed that one of the guide wheels that held the drum in place was sheared off. I took the new d... read more

The Felt Gasket between drum and door ripped, vent manifold from Dryer to fan and lint screen broken

  • Customer: Tim from South Glens Falls, NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 485 of 489 people found this instruction helpful
I pulled the bottom panel and the door panel to replace the manifold and felt gasket around the drum. I removed old gasket very easily, it peeled right off. I use brake cleaning fluid (Spray Can from Auto Zone about $1.45) to remove old glue. Used spray contact cement (Elmer's about 4.50 at Ace) and sprayed the panel and gasket surfaces and let dry. I th... read more

Filter Lint Was Broken

  • Customer: Mirsada from Yorktown Heights, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 372 of 374 people found this instruction helpful
Took it out of the box and put it in the dryer. I could not find this part anywhere else but on this website. The item was delivered the next day to my surprise. read more