ALG331RAW (PALG331RAW1) Amana Dryer - Instructions

I researched the online how to video and when the parts came went at like a pro!

for a while the dryer was really loud when on. i took the front cover, and could pin point it to the idler pulley wheel. i would squirt some wd 40 on the wheel just to get by. one day the dryer stopped turning so i thought the belt broke. after following the instructions on this site on now to take off the front panel, and tub holder (the panel that has the lint trap in it, i was able to take out the tub and find that the pulley wheel had broke apart. i ordered the new part and got a new belt at the same time. why not replace while i had it apart. i didnt have snap ring pliers to remove the snap ring so i got 2 small finishing nails that would fit in the holes and was able to pull apart the ring and get it off. i slid on the new wheel, and put the snap ring back on. ii watch the video on how to replace the belt and it was a sinch. the dryer was already apart and to fix it, took about 15 min. for $18 in parts, the dryer has never sounded better.parts select saves me money everytime.

took dryer apart and replaced the drum support rollers. This did not work and problem is still there. The videos at the part select did not help since they seemed to be for a different dryer and nothing in them helped in any way to work on my unit. I did get a repair man out and was told that he had not seen one built like this one before.

I just followed the intructions from the video on the website. That made the replacement easy.

Pulled the front, loosened the top, released the belt, pulled the tub, pulled the motor, and replaced the idler pulley lever and shaft and the idler pulley wheel, and the belt.

I had two repairs, a few days apart while waiting for diagnosis and parts. I watched the videos and followed the steps, simple as that. I was able to replace the rear roller wheels without taking the drum all the way out. I tried the dryer with this 1st fix, some sounds went away but the worst one remained. Took the drum all the way out and replaced the idler pulley wheel just as the video shows. Everything went back together just fine- no extra parts and the dryer is soooooo quiet. My wife thinks I'm a stud for doing this, thank you partselect.com. A caveat, the e rings that hold the wheels on are a big pain to remove and reapply. The snap ring pliers needed to get these off don't always fit in the little openings to remove the ring.Get the smallest size tips if you buy the pliers. My pliers got an "A" for effort, a "D" for results. I used a pair of slotted screwdrivers to manipulate the rings off. Your mileage may vary.

Motor was replaced with common hand tools, after replacing roller guides and belt.

I knew that it have to be worn out roller drums or the idler pulley with bearing. So, I ordered both items. I watched the repair video to know how to do it. I installed the items and the sound disappeared

I did it just like the man in the video that was sent via e-mail by ParSelect,.

This part fit perfectly. I pulled the old lint filter out and put the new one in with no problems. The part no longer contains a felt seal so if that's your problem just pull the old felt seal off as it doesn't seem to need one.

When the dryer stopped working, I checked the two switches to see if they were good. The start button checked out OK but the switch on the door read bad. Ordered the part with the part number and put on when it arrived. Just a matter of disconnecting and reconnecting three wires. Very simple

No work was required. I just slid the filter in a hole.

Had to call the repair center 3 time & view the video several times because the drum support roller would not fit on the new shaft. Even ordered the parts twice (with refund on first) to ensure the correct parts. The call in center could not help me & I was left on my own. I had to force the roller onto the shaft which was very difficult, Once the hole had gone onto the shaft, it was fine, but I had to take it off to install the shaft then gently drive the roller onto the shaft. It does roll free once over the outer edge. Installing the belt was not easy either. The video did not have a good picture of how the belt runs & not drawing was available, maybe it could be included next time for others

I only had to watch your video! The absolute BEST instructions ever. Your videos have saved me already $480 in repair bills in just one month. First my washer needed a snubber ring, and you had that video and then the dryer parts. Thanks again for being there!

Ordered thermal fuse and cycling thermostat