ALE868QCW (PALE868QCW) Amana Dryer - Instructions

This amana dryer didn't have the lower panel with screws. Instead, I removed the brackets in the back and found that the whole top would separate from the rest of the body (except for wiring, of course.) There seemed to be screws holding the top to the base in the front, but these are just guide posts. There are two spring clips in the front that you can pop loose with a putty knife.

Then there are two screws inside that fasten the front to the rest of the frame. Once I removed these, and the electrical connections to the door switch and the light bulb, the whole front came of just by tilting it forward and pulling the front panel up off of metal tabs on the base.

The rest of the repair went smoothly per other descriptions.

My son will discribe how he did the repair.
First I opened the top, then I removed the front with a 1/4 inch ratchet and socket. I took the cover off the blower housing with a nut driver. Used the appropriate socket and a 1/2 inch ratchet, and an adjustable wrench to hold the motor shaft and removed the Blower wheel. I replaced the broken Blower Wheel and put all it back together.
Our dryer is now working great and there are no unwanted sounds emanating from within. We are very happy with PartSelects promptness and that we recieved the correct part as ordered. PartSelect website was easy to navigate. We plan if the need arises to do so again in the future.
Thankyou Frank and Rodney

I guessed that this was the part needed.............wrong! Changing it out was easy but the dryer does not work any better. I took the back off of the top of the dryer, unhooked the part, pulled the dial off the front and removed it. Put the new one in and put it all back together. No problem other than my guess! The part was great and I got it in an extremely timely manner.

Being my lousy Maytag washer died THE PREVIOUS DAY, spewing water, etc. and I had rushed out and bought a new washer, I was determined not to replace the dryer (though I now am a serious NON_FAN of Maytag).

I disassembled the whole dryer and finally got to the blower wheel which was broken lose from the molded nut. I supposed something like a dime or penny got in there to shred it.

PartSelect's website allowed me to find the part in 5 minutes. It was on my doorstep the next afternoon.

Installation was straightforward BECAUSE I stacked all the screws and and labeled them appropriately. It took about 30 minutes to reassemble and the toughest bit was getting the drum in with the belt positioned properly.

Removed front panels and swiveled lid upwards. Loosened tensioner, removing belt and then carefully extracting the drum. Replaced 2 drum glides on underside of front panel. Next 2 rollers, which appear to unscrew, but do not do so. You must remove the retaining ring (surprise! ...and 2 screw drivers later). This was the longest and most frustrating part of the whole ordeal. Then just reverse the process for reassembly. This was my first electric dryer repair and it really wasn't too bad. Online docs I found were somewhat helpful, but really luck and perseverance. I did save probably $300 in replacement costs, which is quite satisfying. .

Ordered the part, you made it so easy. Received it in two days, very fast, by regular mail. Perfect fit. Pulled out the old broken one and put in the new one!

No problem

Parts that were recommended for the noise issue were spot on. Instructions were very helpful and made the job go very smooth. Replaced the belt, rollers don't forget to order (2) felt pad and idler pulley replaced.
The part suggestions for the heat problem did not fix the problem. The burner flame would come on for 2-5 min. then go off. A few min. later the burner would try to ignite but would not start. The igniter would get cherry red but no activation. I end up replacing the coil kit. Turned off the gas removed (2) screws and wala done 5 min. and it fixed the problem.

I pretty much followed a lot of the earlier postings on partselect.com that provided encouragement to pursue replacing this part on my 17 year old dryer (sorry, money is tight these days and I prefer repair to $800 replacement).

I'd like to add that I borrowed a pair of snap-ring pliers from work which made removal and later securing of roller onto shaft much easier and probably avoided a lot of knuckle bruising and cursing.

I erred though in a couple of places during the replacement. Disassembly took about 20 minutes. However, when I re-assembled I had mistakenly already put the roller onto the shaft before trying to put the drum back in. That isn't possible so I had to remove (an initial groan but only a few extra minutes in the end) the roller from the shaft, then reposition the drum and then the roller back on the shaft.

I also decided to replace the belt while I was in there and I should have taken a picture or made a drawing of the belt route before I took it off since I was later left pondering how the heck to snake the belt onto the shaft and also the tensioner. A quick trip to the internet though showed me a similar route and reminded me how to route it.

I'd also like to add to be cognizant of the wires on the door and front panel when disassembling.

Anyone with any sense of mechanical ability and a little common sense ought to be able to do this repiar.

Thanks Part Select!

Very simple repair. Remove front panel, door, drum etc. Try to keep everything seperated, screws etc. I put lockjaws on the back to get the nut off the front. Make sure to check the housing for "melted on" blower wheel residue. Easy enough to remove. I checked with my local parts dealer he wanted twice the price and needed to order it (at least a days wait). PartSelect sent the exact same part in a day and a half. Put everything back the same way I removed. Hardest part is the drum and belt. While you have everything apart don't forget to clean the thermastats etc. PartsSelect was quicker and cheaper.

Removed power and front panel, removed broken latch, pushed in new latch and replaced the front panel and power. Done

First of all I would not have done this if it wasn't for
your website. Using the schematics to figure out
the right parts was easy. It was also helpful in the
actual repair process. I have added your website
to my favorites in my browser. The parts arrived in 3 days and I live in Reno. Great Website.

M.B.

This is a real easy fix to do by yourself. First, I removed three screws on the inside of the dryer. These hold the air duct assembly in place. Second, remove two bolts on the front-bottom part of the bottom panel. Third after panel is removed loosen the two other bolts and remove air duct assembly. Simple as that.

I took out the old worn out part and replaced with the one I order.

After watching the great install video, I followed his lead and within 20 min had my dryer door fixed. This dryer was bought in 1986 and I really thought I was looking at buying a new dryer. How wonderful that I could fix it for less than $11. Easy to find web site, easy to find part, great instructions and fast delivery!