Quick Question!

Have you ever purchased from PartSelect.com before?

Models > ALE643RAW > Instructions

ALE643RAW (PALE643RAW) Amana Dryer - Instructions

All installation instructions for ALE643RAW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the ALE643RAW
61-75 of 529
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dryer would stop during cycle and then not restart. When I started the dryer, there was a short buzz sound as the motor started.

  • Customer: Bob from Denver, CO
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set, Wrench set
  • 6 of 9 people found this instruction helpful
First I removed the bottom front cover attached with two screws, then the main front cover attached with two screws. I then removed two more screws holding the top in place, detached three wires and raised the top lid. I held the top lid out of the way with a cord tied off to a cabinet above. I then removed four screws holding the front support panel in place and set it to the side with wires still attahced. Then I slid the dryer belt off the drum and removed the drum. Next I removed the cover of the fan wheel by removing several screws. This allowed me to unscrew the fan wheel (reverse threaded) by anchoring the motor shaft with a wrench and using a large socket to turn the nut end of the fan wheel (then was no snap ring). I then popped off the two clamps holding the motor in place and removed the motor. The only tricky part about assembly was putting the belt back on the pulleys once the drum was installed. You can't see the pulleys once the drum is installed so it is done by feel.

Dryer would not heat

  • Customer: James P from Agawam, MA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 5 of 6 people found this instruction helpful
First I turned off the circuit breaker, then removed the two screws that hold the front lower panel in place. Once open I removed the 2 screws that held the element in place. (Far back left side) I then pulled the element out leaving all wires connected. Wires are long enough to extend out to the floor in front of the dryer. I simply exchanged the wires one at a time to the new element so no mistakes could be made. Reinstall, reset the breaker, and Instant HEAT. Repaired for under $40.00

Noisy and not drying the clothes

  • Customer: Pietro from Fairfax, VA
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench (Adjustable), Wrench set
  • 5 of 6 people found this instruction helpful
This was my first time repairing a dryer. If I knew when I started the project what I know now, it would have been an easy repair. First, you should know that the series number (used for selecting a wiring diagram) is the last two digits of the unit's serial number (not model number). In my case, the series number was 11. The hardest part for me was figuring out how to take the dryer apart. I made the mistake of starting with the top instead of the front. In fact, I removed the control panel and disconnected all the wires, labeling them carefully, and creating a diagram, so i could put it all back together later. I now realize I could have left that all together and just lifted the top up in the front without removing it. That knowledge would have saved hours of work, so I hope it helps someone (prop up the front a few inches and start by removing the panel on the lower front, then remove the screws on the main front panel, and then pull out the bottom of that panel toward you until the top of that front panel disengages from the top of the dryer - the rest is obvious). So it turns out there were two separate problems: 1) the blower wheel had broken completely off of the motor so it wasn't spinning - this is why hot air wasn't being pulled through from the heater in the back of the dryer; 2) the pulley on the spring-loaded lever arm attached to the motor was squeaking due to lack of lubricant. So the solution was to replace the blower wheel and spray WD-40 in the pulley (and also, for good measure in the roller bearings that support the drum in the back of the dryer). Most of the time spent on the repair was just due to my own mistakes. In particular, once I got everything back together after the repair, it stopped squeaking and there was good airflow, but it wasn't heating. I spent an entire day trying to troubleshoot the lack of heat. I tested and bypassed all of the thermostats and heater fuses and the heating element still wouldn't come on. I even managed to accidentally ground one of the leads from the fuse and had to replace a melted wire connector (trip to the Shack). In the end, it turned out that a wire which had been accidentally disconnected from the main power cord to the dryer, I had put back in the wrong spot. There is L1, L2, and neutral going into the dryer. I had the heater on the same circuit as the motor and other stuff. Once I traced the wiring diagram back, I realized this and corrected it by putting the heating circuit back onto L2. Now it "hums like a Singer". If everything had gone smoothly, instead of being a 2-day repair, it would have been a 2 hour repair. 2 hours instead of 1 because to get the leverage I needed to remove the old blower nut, I had to actually pull the motor assembly out of the dryer and move it to my workbench. Someone who is strong or more limber or has better tools might be able to skip that step, reducing the time by about 45 minutes. Good luck!

Lint Filter Air Dust Assembly broke inside the dryer.

  • Customer: Loren from Woodland Hills, CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 4 of 4 people found this instruction helpful
I believe the best procedure would be to start at the very bottom of the machine - there are two sheet metal screws in the bottom panel. Remove the bottom panel.

Now, there are two sheet metal screws at the bottom of the front door panel that need to be removed. Remove front panel by pulling down to dislodge from plastic pins aligning it to the top panel.

Now the air duct assembly is accessible. From outside machine remove two sheet metal screws holding lower air duct frame. From inside the dryer opening, remove three screws holding the upper frame. Remove old air duct assembly and vaccuum machine.

New air duct assembly is in one piece, so only three inside screws are needed to support it. Make certain the screws are seated well or clothes could get hung up on the screw heads. Reinstall front door panel and bottom panel.

Doing it this way should make the job around 20 to 30 minutes.

Dryer making a loud squeaky noise.

  • Customer: David from New Albany, IN
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 4 of 4 people found this instruction helpful
Easy repair and done all from the front. Turn off the power at the breaker. Make sure the power is off. Remove 2 screws holding on the lower panel. Then remove 2 screws holding on the door panel. (Pay notice to the order in which the 3 door wires will get re-connected. The 2 light bulb wires probably can go either way.) Then remove 4 screws to a large bracket that supports the front of the drum. (Set these parts aside as you take out the screws.) Then remove the 2 screws from the top panel. Reach in under the drum and release the tension off the belt. It's easy to release, but sorta mind boggling to put back on. Maybe practice that once while it's fresh in your mind. When the belt is off the motor pulley, then lift out the drum. Vaccuum out a lint blanket if you have one. You'll see the 2 drum support rollers and the belt tensioner roller. I didn't know which was squeaking so I replaced all 3. Same method, use ring pliers to take off the retainer ring, remove old, wipe off dust, install new rollers, replace ring. Note the washers are different so put them back on in the same order as removed. Make sure the gasket on the lint assembly gets tucked nicely into the blower housing when you reassemble. Easy repair. If you do pull the dryer away from the wall, replace your flexible exhaust vent with the fire resistant aluminum version.

dryer would shut off during dry cycle. It was difficult to rotate drum manually

  • Customer: Dave from Bend, OR
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Wrench (Adjustable)
  • 4 of 4 people found this instruction helpful
I looked at your on-line diagrams (exploded views) and basically used them as dis-assembly info.

I removed the bottom panel, followed by the front panel, the drum holders and drum.

Toughest part was the spring clips holding the motor in place,,,, but notes on your site from other folks doing the same motor replacement solved that one,,,,,, I used a flat bladed screwdriver and pliers to manipulate the clips both off and on

No Heat

  • Customer: Rogelio from Loxahatchee, FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 4 of 4 people found this instruction helpful
Ordered the new heater element on Saturday and got it on Tuesday. I have ordered from PartSelect before and the service has always been fast and accurate.

The first thing I did was to unplug the dryer and then removed the bottom front pannel by removing two hex screws, one on each side near the bottom of the dryer. Use a flashlight if you need to see better. I then used my shopvac to vacuum all the lint that had gathered over the years, including the old heater element located on the left side towards the back bottom part of the dryer. Located the two hex screws and unscrewed them to remove the heater element. Pull out a bit from the bottom and then down. Pull towards you and remove the wiring from the old heater element making sure where the wiring and parts to be reused go so they could be transferred to the new heater element. Re-attach the heater element with two hex screws. Replace front cover and plug in the power cord and start drying clothes.

Lint Filter was cracked

  • Customer: Rex from Cary, NC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 4 people found this instruction helpful
Not too difficult. Take out of box, insert into dryer slot.
Done

Squeaky belt

  • Customer: Michael from Marietta, GA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 5 of 7 people found this instruction helpful
Removal of the entire 2 front panels
Removal of the heat exchanger into the drum
Removal and replacement of the belt
Reinstallation of the heat exchanger, and both front panels

timer would not turn off drying cycle

  • Customer: Forrest from Dayton, OH
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 4 of 5 people found this instruction helpful
unplugged power cord, pulled timer knob off of stem, removed screws at rear of control panel, swung top of panel forward, LEAVE WIRES ON TIMER, used screw driver to release timer lock tab, turned timer to unlock retaining tabs, NOW REMOVE WIRES ONE AT A TIME AND PLACE ON CORRESPONDING TAB ON NEW TIMER, install new timer by placing tabs in openings and turned to lock in proper position, making sure lock tab snapped into place, put panel back in position, replace screws, replace knob on timer stem, plug power cord in, test cycle for operation,CONGRATULATIONS, it works!

dryer stoped working

  • Customer: Roman from Gaithersburg, MD
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set, Wrench (Adjustable)
  • 4 of 5 people found this instruction helpful
At first i thought i had to buy new dryer, because i did not know what to do.I said, i never done this kind of repair before, well i put everything apart and notice that the idler pulley was worn out, then i said this is something that i can fix it if i get the part. I made several calls and couldn't find it. so went in internet and found it with you.

Squeaking motor, over heating, thermal switch kicking out.

  • Customer: Ernest from Ida, MI
  • Difficulty: Really Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
  • 5 of 8 people found this instruction helpful
Unpluged dryer from outlet, disconnected vent, positioned dryer on side, removed screws from bottom panel, pulled pannel away from dryer body to gain access to motor. Disconnected drum belt from motor pulley, disconnected wire harness from motor. Removed motor mounting bracket assembly and placed entire assembly on floor. Removed clamps and blower assembly from old motor, installed new motor and reassembled. Very easy project, hardest part requires some trouble shooting knowledge to determine the exact cause of problem.

Progressively louder squeaky noise when drying

  • Customer: George W from Austin, TX
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 4 of 5 people found this instruction helpful
I followed the instructions found on this site. The hardest part was figuring out how to release the clamps at the front of the dryer so I could remove the top.

The key was to unbolt the clamps at the back of the dryer first, then to use a putty knife to release the two clamps at the front of the dryer that hold the top to the front.

The rest was easy by following the steps already listed on this site and removing the two front pieces, then the drum and replacing the parts. Putting it back together was simple since I placed things in order and had taken pictures with my cell phone as I went through the process.

The time I took, included vacuuming the inside of the dryer thoroughly. Now it runs like new.

Cycling Thermostat Failed

  • Customer: Jeffrey from Morris, IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 4 of 5 people found this instruction helpful
DIAGNOSTICS: Unplug dryer to reset controls. Remove lower cover. Plug back in. Start dryer. If flame starts and goes out in a few seconds, probably the cycling thermostat (located centrally near bottom of dryer) is bad. It fits in the center of the thermostat heater (not replaced). Use the on-line schematic. I reset the controls (as above) again and jumpered the cycling thermostat. This time the flame stayed on. I turned off dryer before High Limit Thermal Fuse could blow out. Only a trained electrician should do the above.
REPAIRS: Decided to remove main cover, to get better angle on thermostat screws. Unplugged. Removed door first. Be gentle with wires. Be careful with drum, it will simply fall out if jarred. Remove two screws for cycling thermostat. Remove wires, replace cycling thermostst. Reassemble. Be sure drum is still on rollers on back and anti-friction strips in front.
SHORTCUT: If you use an articulated socket wrench on the thermostat screws, you can save your self the trouble of removing the front cover, door, and possibly drum.

Noisy, squealing belt tightener

  • Customer: Randal from Centralia, WA
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
  • 6 of 11 people found this instruction helpful
Changed, got in aimed wrong direction-best to take a digital photo before you disassemble. Overtightened bolt and nut in assembly, it seized. Attempted to drill/grind it off, should have removed motor. Drill skipped up into motor windings. Could have replaced dryer, decided not, fixed by ordering motor, mount, nut and bolt and new belt idler. Reassembly was a snap till the gremlins hit again and I lost one of the drum glides. After a trip across town, I reassembled and it was good to go. Disassembly, use a screw driver to pry up the top, use the nut driver to remove upper front left and right screws, lift front forward and off bottom hooks. You have to release the wiring harness, it has four connectors. Use a sharpy marker and write the wire colors next to the plug-ins connectors you pull gently off and set the door aside. The second wires are two wires for the inner assembly which again need to be marked for color and then pulled loose. Pull them through the plastic hold down so they're out of the way. Use nut driver to remove four screws from inner drum holder, pry gently off dryer blower. Reaching around both sides of the blower housing find the belt tensioner, pull it to the right, push the belt out of it. Lift the drum out, up slightly over the back rollers. Set aside. Use the nut driver to remove the screws into the base holding the motor mount down, now lift the motor/blower assembly forward and pull gently loose from the dryer vent pipe. Set it up where you can work on it. Using the nut driver, take the screws off the blower housing, use a vise grip to secure the motor and use a 7/8 inch turning counter clockwise to remove the turbine. Use the nut driver to remove the screws holding the turbine housing in place, pop the motor clips off. Pull the motor off and remove the nut and bolt of the belt idler assembly using a wrench on the back and a socket wrench on the other side. Reverse order to reassemble, when tightening the idler arm tighten it to where you feel it stop but not any further. Put the belt around the drum again, get it in the previous location on the drum, feel around the drum to make sure belt isn't twisted, bring belt in from the back between the idler wheel and the vent pipe in a loop (Make sure the belt is behind the tension spring rather than in front), Tip the idler arm upward, use the other hand to slide the belt loop up over the motor pulley. One final note is this being a Maytag you might write these direction on the inside of the front panel for next time.
All Instructions for the ALE643RAW
61-75 of 529