AGR5715QDW Amana Range - Instructions

1)Completely removed racks, oven bottom and broiler drawer to access unit. 2)Shut off gas supply by by pulling horizontal lever on left side of safety valve forward to close valve. 3)With screwdriver, removed heat shield covering safety valve and connector from igniter. 4)With socket wrench, removed the two mounting screws on igniter. 5)Installed new igniter, connecting to safety valve. 6)Turned on gas supply by pushing horizontal lever to left of safety valve back to open valve (see step 2). Turned on oven to test. 7)Upon gas igniting, shut off oven and install oven components in reverse order.

Hello,

Your website and prediction that this replacement part was the problem were exactly correct. This part was easy to remove and replace, it is the starter for the oven so it comes with a heating element and a built in connector. I simply pulled the old wires up, unhooked the connector and removed the two mounting screws. Plugged in the new part, pushed the connector back down past the insulation, re-installed the screws and turned the oven on and poof, it started up again. We have also noticed that the oven stays hotter now, just like it did when we bought it.

Thank you very much for the advice and for supplying the correct part. A $65 part is much better than having to buy a $500 new stove/oven. We are very happy we found you and will use you again should some other appliance break down.

Sincerely,
Jim Arao
Seaside, CA 93955

I searched Whirlpool, Sears and random appliance stores and Part Select was the only company to have the lens available. All other manufacturers said the lens was no longer manufactured as a stand alone piece and I would have to buy the entire light assembly. Thank you Parts Select!!!!!

Replaced the igniter as I've done with other products with similar problems. My amp tester wasn't working so I didn't test the igniter. The igniter wasn't the problem so I contacted a repair man who came up with the conclusion that the problem was actually the gas control valve. The valve wasn't letting enough gas to ignite the burner.

I had to pull the range out from the wall and loosen the rear cover to free the connector for the sensor as it got stuck on a corner guide. Put the new sensor in, rear cover back on, range back in place and tested the oven. Oven heats fast now and keeps a more even temp. Makes me wonder how long I was trying to cook with a bad sensor.

This is a no brainer. I am only doing this because you asked. Pull out the stove, tilt it back, remove broken leg, install new leg.

This particular Amana electric range has a "eye" that can serve as the heat source for a small or large pan simply by using the rocker switch to "flip" between "large" or "small." This switch broke. I found Partselect.com, found the part, ordered on Saturday night and received it on Tuesday afternoon. 1) Shut off power to the range at the breaker box. 2) Used a small flat-head srewdriver to pop the old rocker switch from the appliance. 3) Used a set of locking pliers to hold the wires in place as I disconnected the old switch from it's connections using a set of needle-nose pliers. (It was a plug-in style switch). 4) Plugged in the new switch. 5)Released the wires from the locing pliers. 6) Popped the new switch into the range's cabinet. 7) Flipped the breaker to "On". WORKS Perfectly

got new horizontal igniter from Parts Select pulled stove out from wall unplugged old igniter took out bottom oven pan loosened two screws. used same two screws to put new igniter in place, put back bottom oven pan pushed bake button on front of oven and the old was lioke new again

My top burners and broiler were working fine so I knew it was not a gas pressure issue,after reading other peoples oven issues I felt comfortable that my problem was the oven igniter, the igniter was only building about 50 to 75 percent of the normal glow/heat needed, thereby not creating enough heat to trip the sensor that opens the oven burner gas valve. 2 Screws hold a drip pan which after removed allow access to the igniter. 2 Screws hold the igniter in. You need to access the rear of the stove to plug in the new igniter connector at a 1 screw access panel in the center of the back of stove. My oven has been working great since the repair. I would recomend partselect anytime, I ordered the wrong igniter, the diagram is confusing so be carefull , and had to send it back , I got my refund in less than a week. Good luck from beautiful western new york state.

Placed it on the spindle

After reading about my problem, I determined it was the igniter. I immediately ordered one. It came two days later. I took the bottom drawer out and removed the shield. To get to the plug wires, I unplugged the old igniter. I used my power nut driver to take off two threaded screws so igniter could be removed. I then pulled the old igniter out. Plugged new one in and reversed process to install new one. I installed it when I got home from work in less than 30 minutes. all is well. We were looking at buying a new stove for $700.00. I fixed it for less than $60.00. Thanks

took the bottom of oven out.Took the ignitor off the bar. Took the center panel off of the back of stove. Unplugged the ignitor, plugged new one in. Attached ignitor to bar.Put bottom panel back in stove. all done.

removed oven door, removed all shelving....unplugged the electrical cord........unsrewed the igniter(2 screws)removed some of the insulation on back of oven that was covering the wire and plug......disconnected the wire plug...........reversed the process and 15 minutes later I was done............the oven works great.......the new igniter arrived 2 days after I ordered it. thanks

It was necessary to take the decorative glass and metal safety panel off using a screwdriver in order to get to the frame that holds the safety glass. It was hard to slide the new glass into the frame without help from a second person to hold the other pane in place.This was an easy repair to make I would just suggest having 2 people to hole things in place while replacing screws.

1.) Remove door from hinges (open slightly and pull up). 2.) Remove racks. 3.) Remove oven floor to expose burner. 4.) Remove wing-nut and burner cover. 5.) Remove two ignitor mounting screws. 6.) Pull wires and connector through back wall. 7.) Connect new ignitor and mount to burner. 8.) Replace components in reverse order.