AGR5715QDW Amana Range - Instructions

used screwdriver to replace oven igniter , we are planning to buy a new oven in the future , now we can buy it when I can better afford it. Thank you for you help I'll be back.

First off...there are 2 possible oven igniters for this model, and you must determine which one you have. Remove racks from oven.Remove oven door. There are 2 latches(tabs) on the oven side of the hinge.Pull these forward and down. Close the door approx. half way and it will lift straight up. Carefully lay the door aside.There are 2 Phillips head screws at the rear of the pan. They are steel, and may be rusted in place. I used a Dremel with a cutoff wheel to cut a slot in the top of the screw. Then I used a straight blade screwdriver with a pair of pliers on the shaft to assist removing the screws.The oven pan lifts up at the rear to remove.Use a nut driver to remove the 2 screws holding the igniter. Mine were stripped.They use a machine thread in light gauge sheet metal. Then use an air ratchet to put them in. Take a trip to the big box store and get some short stainless sheet metal screws to replace the damaged screws.Pull the wire through the insulation, unplug the old igniter and plug the new one in. Fish the plug and wire back through the insulation. Attach the new igniter with the new screws. Replace the pan with new screws, and reverse the procedure to install the door. Even with the purchase of the Dremel, you will still save a chunk of cash, and you get a tool for the arsenal. It's rare when you don't encounter some problems, with any job. The secret is not burying yourself with more problems you create.

took the top oven door off because you need to reach back to take off the igniter it take a 1/4 inch socket to do this only 2 bolts or screws then slide to stove out a bit to reach the plug in the back of stove its a clip type plug in it don't matter it plugs one way cant get it wrong that it put the new on but slide the plug through the hole in the back of the oven first then bolt it back and your put the clip on in the back of the stove. turn it on. mind came on fast and that is what you want it to do your done. this repair is in the bottom in the broiler area might need a flashlight to see with.

Shut off power, pulled oven out, shut off gas, removed racks and bottom cover. Two bolts held the igniter on, remove those and feed the electrical connector plug through the back of the oven and replace igniter. Be sure the bolts are not too rusty as one if them sheared off and I had use a pair of side cutters to hold the screw while I removed the broken section of the screw.

I'm a girl, blonde, and fixed it! Oven just turned 10 in July. I removed oven racks, then used screw driver to remove two screws for the lower panel. Used screw driver to listen the two screws that hold igniter in place, then wrench to remove. Pulled wires out from hole in back of oven, unplugged old igniter, used needle nose pliers to hold wires in place from slipping back through hole, plugged in new, pushed wires back in, screwed it in, turned oven on to make sure igniter worked, it glowed, turned off, replaced lower panel, turned oven on again to let it light up, it did, screwed it in, replaced rack, closed door, preheated oven, and then baked cookies! Great company, great customer service, and super fast shipping!

Replaced igniter, removed inside bottom cover 2 screws,removed igniter 2 screws & unplugged igniter from back of oven after removing plate with 1 screw. Could not have been any easier took less than 10 minutes. And doing business with PartSelect was great, would recommend and use again any chance I get.

I have and in the wall Magic Chef oven CGW3330ADW seriel 10799876US that came the purchase of my home 10yrs. ago. After a black out and 2 brown outs my oven would not start and the F3 code is beeping and the "door lock" light was on but the door was unlocked. The clock was working fine, but could not use the timer or set the temperature. I googled "FLASHING F3 code" and one of the results was the comment thread on the Parts Select website. When I clicked the link I read several customers sharing their story that was very similar to mine. I was able to click on a video and see a short demonstration on "HOW EASY" it was to replace the "Short Oven Sensor Kit." I though, "Yea right!" I left a comment on that You Tube video with my make and model and a brief explanation of my problem. I received a reply to my comment with in 24 hours, confirming what other consumers had shared...The "Short Oven Sensor Kit" was needing to be replaced. I ordered the part for around $30 VERY late on Thursday evening and when I woke on Friday morning, I a shipping confirmation email. I received it VERY early on Saturday morning! I was able to replace the part very easily with in about 10 minutes. I was VERY LUCKY that I was able to to the repair WITHOUT having to remove the oven for the wall! I would have had to pay for help if I had to remove it from the wall. The Parts Select web site save me over $400 which was the estimate for the parts and labor from a local appliance repair business! I was told that it would probably be cheaper or about the same as buying a new over which was their recommendation. I am so glad that I decided to do the research and in less that 1 hour I had my order placed. Thank You Parts Select!

removed two screws from ignitor, pulled connector from hole behind it, replaced ignitor, reconnected. tried the oven and it worked first time. easy, easy.

Removed the racks inside the oven then (2) screws that hold the bottom cover. Once the cover was off I exposed the burner element. I Removed (2) small Philips screws that held the unit. I removed electrical plug and the unit was out. I replaced the part and put everything back together. This was a very simple job took me about 10 minutes to complete. gas company wanted to charge $130 just to come out and look at. I saved some good cash.

removed oven door and shelves and lower pan and replaced igniter

I removed the sensor from the oven using a philip screw driver. The sensor was removed by removing the two screws holding it in place in the upper left hand corner of the oven. I had to disconnect the sensor on the back of stove. Then I pulled the old sensor through the hole inside the oven. Then I installed the new sensor by putting the wire of the sensor through the hole where the old sensor was removed. Then I hooked up the wire in the back of the stove. Then took the screw driver and replaced the two screws holding the sensor in place. It was very easy to do and the oven is doing fine now.

Cut off the electricity at the junction box. Removed two screws from the sensor at the back of the oven. Then pulled the sensor with the wire out of the installation hole in the back of the oven. Disconnected the quick connect plug from the sensor and reconnected the new part. Reversed the process and screwed the two screens back into the oven wall. Turned the electricity back on and started up the oven. (Everything ran well for about three days when the oven again signaled "F-5" indicating the oven was again not functioning properly. Restarted the oven and is currently running properly. My spouse does a lot of baking with this oven for cookies, roasts, etc. Next time it fails I will be forced to call a repairman as I believe there is something wrong other then the heat sensor.

unplugged range took the oven racks out removed bottom plate, removed 2 screws from the igniter, wiggled the connector out of the hole, unplugged the connector. reconnected the connector reattached the igniter and put the plate and racks back in plugged the range in and it works just like it should. took about 15 mins. easier than I expected.

the repair was not difficult ,take time cause back panel has to be removed to gain access to unplug the temp sensor ,it appear to work but the digital clock still flash not all the timebut it should not flash , not sure that i have fixed it

Easy just loosened screws took apart door, removed broken glass and installed new glass.It took longer to clean the stove! Lol!