AGM479L2 Dryer - Instructions

Disconnect power supply. remove two 5/16" machine screws from bottom front cover, pull out and down cover will pop out. open door and remove lint screen. Remove screws from top of dryer and pop it off and get out of the way. Now remove front panel and lint screen body. there are screws inside of dryer for screen body. Make sure to take photos of wires or make a diagram so you put them back correctly. Now you can remove drum and see pulleys. This is all pretty self-explanatory. Just re-assemble in reverse. Whole project takes maybe 45 minutes.

Push new catch in the opening, close the door and VOILA! the door stays closed. Please note that the cost of this part is exorbitant- it's worth about 50 cents but with shipping it cost about $11.00. Check your local hardware store first.

Turn off dryer 220V breaker at panel. Remove front kick panel (two 5/16 hex screws at lower corners). Check continuity of high limit thermal fuse with meter; no continuity: fuse blown. Remove two wire clips with pliers. Remove fuse with nut driver (two 1/4 hex screws). Install new fuse. Replace two wires. Replace kick panel with two screws. Reset breaker at panel. Reset, start timer: dryer has heat.

After ordering the part, I read the information left by other users. I used a screw driver to pop out the piece, and then put the new latch in the opening. A gentle pop with the side of my hand, and the door latch went right into place. Who knew there was a second door latch on the other side that could've been used?

Unplug the Dryer; remove the lower exterior cover and white plastic drum vent with nut drivers. These two fuses will be setting on top of the function board in front of the gas heating tube.
With a short screwdriver, remove the fuse cover/holder, lift fuse and unplug, replace, re-plug, screw back the cover/holder and you’re done.
Reverse your initial actions...

I replaced the two drum support rollers, the idler pulley wheel, and the belt. Replacing support rollers and pulley wheel requires snap ring pliers, to spread apart the tiny retainer ring that holds the wheels onto the shafts. Get a good quality one! The $23 pliers at Home Depot works great. The one I got for $3.99 online was garbage, and caused me to break one of the retainer rings. I'd recommend buying an extra retainer ring before beginning this repair, and practicing using the pliers with it. It's a very delicate operation and you have to have a steady hand. RE the Idler pulley wheel - this was the most likely cause of the squeaking noise. The old one had a deep groove worn into it by the belt, which may have caused it to spin off-balance on the shaft, resulting in the squeaking noise. RE replacing the belt: at first this task looks impossible, because you can't see exactly how the belt is threaded until you fully remove the drum, but you can't remove the drum until you've removed the belt! Put your hands behind and try to feel how it's threaded, before removing the belt. I drew a diagram to help me visualize how the belt is positioned: looking at the drum from the front, imagine the belt running clockwise around the drum, and after it goes across the top of the drum to the right, it threads UNDER the idler pulley wheel, then clockwise around and under the motor shaft, then back under the drum and around (I hope this helps, it's hard to describe in words). To replace the belt you need to first remove the two screws that secure the top panel of the dryer, and lift the top panel up (like the hood on a car). Then the sequence of steps to replace the belt is: 1) slide the belt off the drum, toward the back of the dryer. 2) remove the drum from the machine 3) if belt is still threaded, make a note of how it's positioned 4) Remove the belt completely 5) thread the new belt under the pulley wheel and around the motor shaft as described above, and 6) keeping the belt fairly taught, place the drum back in position and slide the new belt around the drum in the reverse direction, from back toward front. 7) test the belt by rotating the drum a little to ensure the belt and motor are rotating smoothly together. IMPORTANT: the ribbed-rubber inner side of the belt must be in contact with the drum and with the motor shaft. The belt may twist as you're putting it on, so feel it all the way around to make sure it's flat, and untwist it if necessary. Hope this helps -- it will make more sense when you're actually doing it. Though this may all seem complicated, it's actually a fairly simple machine with only a few moving parts, so it's not as hard as I am making it sound. Courage, and good luck!

I replaced the two coils that regulate the gas to turn on and the other to hold open to burn, unplug two connections and remove 2 screws and then replace the coils less then 5 minutes to do this,

Took apart front and top panels. Eight screws in total. Removed belt from pulley then drum. Removed both support rollers, idler pulley. Installed new items. Five wires that must be removed and reinstalled. I made diagram of wiring. Drum glides remove easy. Install new ones. It is best to install the belt on drum, then on the pulley. Install all panels.

I researched the online how to video and when the parts came went at like a pro!

for a while the dryer was really loud when on. i took the front cover, and could pin point it to the idler pulley wheel. i would squirt some wd 40 on the wheel just to get by. one day the dryer stopped turning so i thought the belt broke. after following the instructions on this site on now to take off the front panel, and tub holder (the panel that has the lint trap in it, i was able to take out the tub and find that the pulley wheel had broke apart. i ordered the new part and got a new belt at the same time. why not replace while i had it apart. i didnt have snap ring pliers to remove the snap ring so i got 2 small finishing nails that would fit in the holes and was able to pull apart the ring and get it off. i slid on the new wheel, and put the snap ring back on. ii watch the video on how to replace the belt and it was a sinch. the dryer was already apart and to fix it, took about 15 min. for $18 in parts, the dryer has never sounded better.parts select saves me money everytime.

I followed the instructions provided by Partselect. The video and information were very clear and accurate. I have never taken a dryer apart, but have some tools and the cost savings plus the reward of fixing it myself were enough to inspire me to try. I was so happy with this experience I recently diagnosed and fixed a friends dryer with the helpful information from Partselect.

Igniter would glow and flame would burn for about 30 seconds then a rattling noise would start and the flame would go out. Replaced the coil and all is well. Very simple and inexpensive. One of the easiest repairs I've ever done. Video was very helpful.

I recently found your site and was pleasantly pleased with your troubleshooting suggestions and repair videos. My dryer was sounding like there was a pair of gym shoes inside bouncing around and your suggestion of the drum support rollers was right on the money. My dryer cabinet came apart a little differently then what the video showed but was workable.
I would like to suggest sending the washers that go in front of and behind the drum support roller with the drum rollers. The washers on my dryer were completely ground down to powder so I drilled out some stainless steel washers I had in my supply of extra parts. These washers are hard to find in a hardware store due to being so thin.
I would suggest to anyone changing these drum rollers to go ahead and order/replace the drum belt and front guides as long as you have the machine apart and had to take these off to get to drum rollers. I have had my dryer maintenance free for 17 years and figured they were probably close to being worn out as well. My front guides were paper thin and the drum belt had lots of cracks.
Total cost of bringing dryer back up to par was only $45.00. Saved at least $180.00 doing myself.

Both washer and dryer always worked perfectly. Suddenly, dryer wasn’t drying laundry properly. Problem... no heat. Cheapest price I could find calling for appliance service was about $160 to replace coil set but no one would tell me this would fix the problem. This was after calling a number of repair firms and trying to get a somewhat close estimate of what my problem was and what the repair cost. Not knowing, I might have just paid the $160 but what turned me off was having a service call fee of anywhere from $50-$80 with no one willing to tell me what the problem might most likely be before coming out or give me an estimate over the phone other than a range of $160 - $275. I just did not want to have someone come out for $50 -$80 and tell me that I needed to spend $275 and still owe them the service call even if I did not agree.
Found diagnostic and repair instructions help on line. The diagnostic information indicated a high probability, roughly 50%, that replacing the coil set would solve the problem and found the coil set cost $19.21 plus shipping, so I ordered the coil kit for total of $26.70. Note... I am a 71 year old amateur never having worked as a repairman of any kind except for my own needs.
The repair itself took less than 30 minutes start to finish and was one of the most straight forward, glitch free, easy repairs I have ever done. This is a gas dryer but still uses 110 power so I unplugged the 110 power cord from outlet. Followed suggested guidance on opening the dryer cabinet from the front and presto, the coil set I needed to replace was immediately right in front with easy access. Removed 2 screws for the hold-down bracket, slipped off both coils, one at a time, removing the wiring connection for each coil and then reconnecting to each new coil before slipping each new coil back into place and reattaching the hold down bracket. Reinstalled the dryer door and cabinet front in reverse order from taking off... 4 screws total. Plugged in the 110 power cord and put in a damp load of freshly washed laundry. Presto... 30 minutes later... dry laundry. Note... could do the same repair again in half the time since I took it slow and careful 1st time and also took time to remove dust before completing repair. I like things to look like new inside and out and it did when I was done. $26.70 and good as new. Why I didn't spend $160 - $275 is pretty obvious now.

Open dryer door, remove old lint filter, replaced with new filter. ;)