Models > AFI2538AEW00 Maytag > Instructions

AFI2538AEW00 Amana Refrigerator - Instructions

All installation instructions for AFI2538AEW00 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the AFI2538AEW00
571-585 of 604
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

I replaced the end panel where a plastic hinge pin had broken

  • Customer: Stephen L. from North Palm Beach FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Remove the shelves and the other trays. Use the nutdriver to extract the screws and the panel. Pay attention to the orientation of plastic parts when replacing plastic slides to avoid breaking the plastic slide components. Avoiding too much stress on plastic parts is important.

Tab on the end cap broke off

  • Customer: Bernard from Ashburn VA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Remove the pantry drawer door, then remove the pantry drawer. Remove the 2 vegetable bins to gain rom to see and to ease access. Remove the 2 screws holding the end cap to the interior of the box. remove the slide from the end cap and place it on the new one. Reinstall the end cap being sure to have the tabs go into the slots at the back. Make sure the end cap also mates with the tab in the front, Reinstall the drawer and the bins and the pantry door.

The hinge pin broke that holds the door on the full-width vegetable drawer

  • Customer: Leonard from Lexington MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I removed all drawers (including the two above the repair site, removed the left side end cap - it was help in place with only two screws (one screw hole appears never to have had a screw). Swapped out the broken part for the new one, reinstalled the screws, put the drawers back, mounted the operable door to the two hinge pins, and things were fixed.

Broken pantry end cap

  • Customer: HARRY from Boynton beach FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Ordered parts on Tuesday. They arrived on Thursday and I completed the protect SAP.No Problem at all.I used hints from others,removed the 3 screws with my nut driver and completed the job as a pro.My Bride(of 63 years) was amazed at my ability Thank you Part Select.I informed all of my Family members of your prompt service

Replace Pantry End Cap due to the hinge breaking off.

  • Customer: Patricia from Escondido CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I removed salad and veg draws, pantry draw and the two glass shelves. Located and removed the screws holding the pantry side, gently eased the side out and replaced with the new one. Just a breeze to replace and for a 73 old female, pretty good. Thank you PartSelect for speedy delivery of part.

water filter 1 year old. Light bulb burned out.

  • Customer: Chuck from Harbor Beach MI
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Unscrewed old water filter. Screwed in new filtr. Moved lense off track. unscrewed bulb. Screwed bulb. Slid lense back in.

leaking at tube where water filter is

  • Customer: Jodi from St. Clair Shores MI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
you snap out old part pull waterline out of tube going down to the back and unplug tube on top connection ,,that was tricky ,,revirce for new part but you guy should make the water tube attachment on the water line match what is out there that you buy at the stores .I had to go back 3 times to get the right part to get my water line to connect with yours ..

center rail for vegetable and fruit drawer was broken

  • Customer: Mary from St.Charles MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Removed both drawers and glass shelf just above the drawers. Center rail just fit into place. Replaced glass shelf and both drawers. Took no more than 5 minutes.

Broken rail

  • Customer: Joseph from Mountain top PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I replaced the broken part. There was one bolt to loosen with a nut driver. I disconnected the original wiring harness, reattached the new harness and reinstalled the hinges, which simply slide into place. Then I reinstalled the small bolt I had removed with the nut driver. The job was with no problems.

door slamed and broke the two pins on deli tray end caps

  • Customer: james from lake worth FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
broke pins wed. morning ordered end caps wed. afternoon parts arrived next morning at 9:30 had it fixed by 11:30 30min repair time and i'mm 77years old. Out standing service. Removed veg. trays removed glass above deli tray removed broken pantry end caps installed new end caps two screws each.Very easy,took less than 30 min. Thanks

Broken tab on right side of meat/cheese lid

  • Customer: James from Dewitt MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
1.remove upper cold storage bins 2.rremove top glass on lower storage meat/cheese bin. 3.remove trim parts from front and rear 4. remove bin 5. remove trim pieces and slider mechanism from right side and back. 6. replace with new parts. 7. clean out gunk which accumulated on bottom of fridge. 8. reassemble in reverse order 9. Took longer than anticipated...over one hour.

Moved into a new apartment and this part was missing from the refrigerator so the bottom crisper was not functional.

  • Customer: Linda from Biscayne Park FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Was a very tight fitting part and it had to be gently tapped into place.

stopped chilling

  • Customer: Dave from Harrisville UT
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I did a Google Search for a 1998 Whirlpool ED22RF, looked for trouble Isolation procedures. Don't remember the web sites but two parts were mentioned namely the timer and the thermal relay. After making sure it was unplugged I removed the back lower insulation panel, removed the red wire from the relay located on the left side of the condenser and unplugged the relay. I examined it for physical damage before checking with an ohmmeter and found the thermal relay sounded like it was full of sand when I shook it. So we found PartSelect and searched for the thermal relay and found an exact picture with the part number and ordered the part. We received the $30 part 5 days later. Only took 15 minutes and two tools to install. Thank you for saving us a few hundred dollars.

compressor clicks on for about 5 seconds and then shuts off, evaporator fan is running but no cooling in the fridge.

  • Customer: Scott from Jay ME
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Disconnect power. Remove back panel on the refrigerator. Relay and overload is a modular unit attached to the compressor. Disconnect module from compressor, install new unit. While you're in there clean the condenser coils with a vacuum and clean the fan and condensate pan. Reassemble, and you're chillin. Total time approx. 15 min.

CENTER RAIL END TAP SNAPPED OFF, AND CRISPER DRAWER BROKE HINGE TAB

  • Customer: William from Ridgely MD
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
REMOVED BOTH VEGGIE CRISPER AND LOWER CENTER CRISPER, REMOVED GLASS SHELVES, REMOVED BROKEN SIDE PANTRY END CAP TWO SCREW, TWO WERE MISSING. HARDEST PART WAS TO REMOVE THE REAR ADJUSTABLE PIECE AND INSTALL ON NEW END CAP. GLAD I TOOK MY TIME AS THE CENTER RAIL WILL PROBABLY HAVE TO BE REPLACED AGAIN. POOR DESIGN, NUMEROUS OTHER COMMENTS SAY THE SAME THING. BEST PART OF THE REPAIR WAS ORDERING FROM PARTSELECT.CO, SHIPPED ON TIME AND ORDERING WAS EASY WITH COMPLETE PARTS DIAGRAMS.
All Instructions for the AFI2538AEW00
571-585 of 604