AFI2538AEW Refrigerator - Instructions

had to replace the whole right side panel, came off fairly easy, but to get the adustable rod out and back into the new panel was somewhat difficult. I found out you can bend more than what you think to get it out and back in. It is the rod that adjusts the air flow

Changed bulb, not the problem, had to remove switch to identify correct choice to order (3 pronged verus 2) after that it was easy beyond having to stand on my head to make the exchange. (N B before removing old switch it actually came back to life)

I'm a 65 year old widow on a limited SS income, so I needed to get my refrigerator fixed as cheaply as possible. Partselect's troubleshooting guides took me right to the problem. I ordered the part on a Friday and it arrived the next Tuesday. It probably took me a little longer than it would a repairman, but I did it myself with just a screwdriver and a nut driver and it only cost me $45 instead of the $200 plus it costs my daughter to have someone else replace hers two years ago. Always remember to unplug amy electrical device before removing the covers or attempting any repair. All I had to do was remove the lower back cover on the refrigerator and, using the partselect diagram, locate the casing that covered the start relay and the overload switch on the left side of the compressor. I popped the casing off with the screwdriver, pulled the relay off (it's sits on two prongs), and remove the red terminal wire from the relay. Installation of the new relay is the reverse steps of the removal. Thanks, Partselect! I will be doing business with you again if the need ever arises.

removed the broken bin, which was extrememely easy and set in the new one, equally as easy. The telephone staff were extremely helpful, and courteous, especially John, who took a great amount of time helping me find the correct part. Thank all of you.

Right part for the unit. A bit of a learning curve but like new.

popped out the old lid and put in the new one,great service and arrived quick.

The little knob that holds the door onto the deli bin had snapped. I ordered the part, it arrived within a couple of days. I emptied the necessary shelves, cleaning as I went of course. Removed the old part and installed the new part- instructions weren't necessary. I had the part back in within a few minutes. Someone else had reported that it took longer to remove the shelves and replace them than it did to replace the end cap. I found my experience was the same. I was very proud that I didn't have to ask my husband to do the repair for me- I did it myself.

had to remove old end cap and back piece, remove slide and replace on new part.

Simply replaced broken middle drawer with new. Works fine

Pulled off tape on old toe guard, removed it, it was trashas is the whole refrig. then installed the new onefits great, snaps in place and is 100% better quality then the one that came w/ refrig..then it was on and done, stays inplace and looks great..thank you, and the price was half of the price I got from Maytag and Lowe's..Good job U folks will get my business from now on..Also, I received in one day. dkh

Had to remove bottom drawers and glass shelf, unscrew 3 screws, the right side end cap controls the air control so there is another piece that is attached to the end cap that has to be removed from the old and put on the new cap. And do replace this part since it controls the temperature of the refriferator if not the alarm goes off.

I opened the cover to the filter and screwed the filter counter clock wise until it came loose then removed the old filter and put the new one in. It was real easy.

It was very easy, just unscrew old filter and screw in the new filter. Reset the warning light, and done. Ralph Mason, 403 Sundance Lane, Georgetown, TX 78633

(Always pay attention to where parts are located and how you remove them.) 1) Remove vegetable and fruit drawers above the pantry. 2) Lift out the glass pantry top. 3) Remove the rails which support the glass pantry top and remove the pantry drawer. 4) Operate the temperature control lever on the end cap while observing the movement of the sliding vent covers just above the back of the pantry drawer. 5) Remove the 3 screws which secure the end cap. 6) Carefully pull the end cap away from the side of the cabinet, taking care not to break any of the attached pieces. 7) Remove the components that control the temperature of the pantry. Some must be rotated to bring the component through a slot (or similar arrangement) - the control arm snaps into a hole in the center back of the cabinet... so you may need to use a flat screwdriver to assist in freeing it. 7) Install the components just removed onto the new end cap. 8) Re-attach the control bar in the back of the cabinet. (Its other end is now attached to the new end cap.) 9) Position the end cap and secure it to the cabinet with the 3 screws. Before snugging them up, test them to insure that the temperature control is sliding correctly. 10) If all is well, snug up the screws. 11) Re-install the glass support rails, glass, pantry drawer and the veg and fruit drawers. 12) Place the left end of the front cover of the pantry drawer on the hinge pin on the left side. Carefully bow the cover to allow the right side to be slid over its hing pin on the right end cap. Job done. In the future, take care to insure that the pantry draw is pushed in and the cover is closed BEFORE you close either of the two doors on the refrigerator!

Couldn't have been easier. Remove the glass plate. The deli drawer lifts out of the slides. Two screws later, the entire assembly was out. Be careful with the adjustable vent that is attached to the right end cap. Gently pull out the end cap, the vent just has a tab on the very end that inserts into the rear wall of the fridge. After that, reverse for installation. JMC