Models > ADW862EAS (PADW862EAS0) > Instructions

ADW862EAS (PADW862EAS0) Amana Dishwasher - Instructions

All installation instructions for ADW862EAS parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the ADW862EAS
46-60 of 701
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Rusted upper and lower racks, broken tines

  • Customer: Charles from Phoenix AZ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 11 of 12 people found this instruction helpful
Read the experiences here, very helpful. Bottom slides out first - really easy. The new part comes with rollers, you don't need to remove the old ones. Now the only problem, getting the sprayer off the bottom basket. Look carefullty, you must use a screwdriver to release one side of the sprayer, then it works off easily. Make sure you note the orientation of the base of the sprayer. Reverse steps above and you are done. New tray slides in. Our new tray was a bit wider than the old one so we needed to use a bit of pressure to "shrink" the back just a wee bit.

The upper is easy also. Since the rails are uneven, make sure you put the high rollers on the high side no matter what your wife told about how it is supposed to go in. The end caps snap inward and slide out of the rails. Easy once you know. The uneven rails are obvious once you notice. Total time was 45 minuts, 30 of which was figuring out how to get the sprayer off without damage.

Would be nice to know the factory recommendation for removing the sprayer.

water was dripping from the bottom of the front loading door. Over time this had seeped into the insulation foam strip and formed a solid encrustation within the foam strip.

  • Customer: Dan from Clarkston MI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 11 of 12 people found this instruction helpful
The real cause of the leak had nothing to do with the foam strip. The latch for the front loading door at the top needed to be adjusted to hold the door in tighter to the rubber door seal. This simple adjustment stopped the leak but since the foam seal was all encrusted with dried detergent from probably years of absorbing the leak, I replaced it with your new foam strip. I used a screw driver with torx bit and removed the stainless screws holding the inner door to the outer door. Once these were separated I removed the old foam strip using a putty knife and lacquer thinner. Placing the new strip onto these cleaned surfaces was the easiest part of the whole repair.

No water in the washer barrel

  • Customer: Terry from Great Falls VA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Wrench set
  • 10 of 11 people found this instruction helpful
Diagnosed potential problem from scematic diagram found at Parts Select .Com by entering model #. It was very likely the inlet water solenoid. Tear down was simple: Turn off water, disconnect water lines to and from solenoid, disconnect two electric terminals and remove part by removing two screws from dishwasher chasis. Before you buy the new solenoid, unscrew the water inlet elbow from solenoid and check the filter/screen inside the solenoid to make sure it isn't clogged. Assuming it's not, order the replacement part and reinstall in reverse order. Be sure to use plumber's tape on screw connections to make sure there are no leaks..... Also for ease of acces, you'll need to turn the dishwaher down on it's front. Put towels down to cushion the front and keep the controls from contact with the floor. Good luck!!

Upper washer arm holes plugged up

  • Customer: STEVE from RAYTOWN MO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 10 of 12 people found this instruction helpful
The upper washer arm can be removed by just snapping it out of place. Just take a screw driver and put in underneath the spray arm and pry it out of its socket. It will just snap out its place. Sometimes this retainer will break so make sure you have this retainer before trying to remove the upper spary arm. I removed the spray arm and back flushed it out with a garden hose to get the debri out of the washer arm. The holes are all clean now. Washes much better now. To put in back on just put the washer arm back where it goes and then just snap the clip back in its hole. Pretty easy fix.

Racks were rusting, pieces braking off and rubber coating was peeling.

  • Customer: Lora from Plover WI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 18 of 36 people found this instruction helpful
Was extremely easy to remove that existing rackings(upper and lower), install the new racks and snap in the new spray tower. It now looks like we have a new dishwasher. We are hoping that it will last another 10+ years.
We will recommend your site to friends.

Leak in the hose that feeds the upper wash arm

  • Customer: Norman from Chappaqua NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench(Adjustable)
  • 9 of 9 people found this instruction helpful
First I disconnected the dishwasher electric, water supply and discharge hoses. I then pulled the dishwasher out. After opening the door, I removed the retainer clip holding the upper wash arm, then the nut holding the top shower hose in place. Close the door and lean the dishwasher on its side to get at the underside where the other end of the hose is. Loosen the hose clamp and remove the top shower hose. Reassemble everything in reverse order. In hindsight, I didn't need to buy the new hose clamp or the tub top washer (I reused the originals). Good luck!

soap door didn't open

  • Customer: Richard from Shelburne Falls MA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 9 of 9 people found this instruction helpful
I took out both wax motors - tried switching the motors on the rinse dispenser and soap dispenser but they were both dead - new motors from partselect arrived fast - simple installation if you have the torx screwdriver for the door inner panel.

Pump gasket had deteriorated with age and causing odors.

  • Customer: Kenneth from Brooks GA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 9 of 9 people found this instruction helpful
The dishwasher is well engineered to perform this work.

Remove the bottom two panels to provide access and visibility to base of pump motor.

Locate plastic pump locking lever and push toward rear of DW to unlock pump from DW.

Inside the DW remove basketsand spray arms. Revove screws holding cover over pump motor and remove cover.

From below raise pump motor and support with block (piece of 2x4 worked well).

insde DW, removre old gasket, clean well around pump and botom of DW, install new gasket.

From below remove block to drop pump motro back into place, and re-tighten locking lever by pull toward you.

re-assemble inside componets, run through a rinse cycle to test for leaks and replace bottom panels.




I

Leaking

  • Customer: L W from Manning SC
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 9 of 10 people found this instruction helpful
I first changed the dispenser door latch grommet, which was very eazy except for the left side nut screw which was a little awkwaed to get to with the nut driver. Not a big problem but difficult enough that i stripped the threads (plastic) and had to get a larger screw which is working fine so far. Since the grommet didn't stop the leaking although it was obvious it was leaking from the soap trail. I ordered the gasket and got it very promptly put it on and guess what. Still leaked some. I discovered when they installed the dishwasher the door appeared to be warped. To fix this there are two door tension springs under the bottom panel. By adjusting these with a log screw driver problem finally solved.
It is good to have not only a great place to get parts but the idea's from others are terrific. Although this washer is 15 years old it looks new and now acts new. Thanks so much for good service and advise.

Maytag dishwasher was leaking from front, bottom right corner

  • Customer: Mike from Fairfax VA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 9 of 11 people found this instruction helpful
We simply removed the old gasket which was corroded, cleaned up the hard water buildup, and popped the new gasket into place. The problem was fixed! No more leak!

Changed the heating element

  • Customer: Ron from Osage Beach MO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 10 of 14 people found this instruction helpful
I first disconnected power from the dishwaher at the breaker panel. Then, removed 4 screws on the front of the dishwasher and removed the lower panel. I removed the two wires (compression fittings, by hand). Then I used an adjustable wrench to remove the two nuts which retained the element. I opened the diswasher door and extracted the old element. I reused the rubber O-rings from the old element and placed the new element into the dishwasher. I replaced the nuts and wires. I reenergized the circuit and ran the diswasher through a normal cycle. Note: I had plenty of towels on hand just in case the old O-rings did not perform. No problems encountered. I replaced the front cover and loaded have checked under for leaks during the last two wash cycles. Note: be sure not to over tighten the element nuts as they are plastic and will strip out. I used the model number to obtain the new part and all went flawlwssly. Thans!

Rusted racks

  • Customer: Paul from Anaheim CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 8 of 9 people found this instruction helpful
Most difficult was figuring out how to release the top rack...just flip the end pieces to the side and out they come. Next was removing and reinserting the spray head in the bottom rack...just twist and take out then align and twist into place in the new rack.

dishwasher leaked

  • Customer: Jean from Gaffney SC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 8 of 9 people found this instruction helpful
First replaced rubber seal around door, which did not stop the leaking.
Then ordered insulation foam strip and replaced old one, which fixed problem. Put new strip over the old one because tub was slightly warped.
Very pleased with order speed and cost.

leaking drain hose

  • Customer: David from Wilmington NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 9 of 13 people found this instruction helpful
removed clamps with screwdriver from bottom of dishwasher and clamp from sink drain. I taped the new hose to the old one and pulled it through. worked perfect.

Leaks on floor in front of washer.

  • Customer: Jim from Yorba Linda CA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 7 of 7 people found this instruction helpful
Removed two lower panels using nutdriver. Ran washer through a rinse cycle, to determine for sure where leak was coming from (under door on left). Examined the door gasket and observed buildup of lime deposits and a general depression of the gasket through years of use, especially in lower portions. Removed the old gasket observing how installed. Cleaned out groove with Lime-away and toothbrush. Washed clean using water in a squirt bottle. Dried things out using paper towels, and then pressed new gasket into place, starting at lower left. Readjusted the gasket to fit precisely end to end. Shut door and ran a drip free load.
All Instructions for the ADW862EAS
46-60 of 701