Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
latch on soap dispenser failed
I removed the 10 screws that hold the front door panel on and then I removed the 6 screws that hold the dispenser in place, pried slightly on the 2 clamps that hold the dispenser in place, unplugged the wire to it and pulled it out. Put the new one in and reversed the steps. Presto done! Works great. Thanks Parts Select. PS Kitchen Aide come up with a better design!
Turned off power, turned off water supply and diconnected, slid out dishwasher. Removed the spray wand and tilted dishwasher to access the two nuts and disconnet the wires. Removed the two nuts using a socket. Removed the old heating element and replaced with the new one secured with new nuts ( the old ones were fine but since I bought two new ones why not). Pluged the wires back up slid the dishwasher back in hooked up the water reinstalled the spray wand cut on the water and power. Good as new.
spray arm did n't move because it had a crack in the end
First I had to remove the upper dish rack from the dishwasher. This was the most difficult part of the entire fix. I found the screw which holds the spray arm in place, Removed it and took off the old spray arm. Then I replaced the seal and put the entire thing back together, put the screw back in and replaced the rack. Then I ran a load of dishes and discovered the machine works just fine now.
The ceramic seal had failed, allowing water to destroy the front motor bearing.
Removed dishwasher from under the counter and took it to my shop. With the washer on its side, I removed the motor, then the impeller and seal. I then disassembled the motor and replaced the front bearing(purchased separately). This required an arbor press. I then reassembled the motor and installed the new seal and impeller. Reassembled in reverse order. Reinstalled under the counter and made conections. Checked for leaks and proper operation.
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
19 of 26 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dishwasher wouldn't heat water or dry dishes
Disconnected the power and hot water supply. Removed mounting screws under the counter, and the lower panel screws to expose the leveling screws. Backed the leveling screws up so that the unit would slide out more easily Walked the unit out to where I could reach the back side. Disconnected the two power wires from the heater coil (slide off) Unscrewed the plastic nuts holding the heater in place and removed the heater coil. Replaced the heater coil and nuts. Reversed the process above to install.
I watched the instructional videos that showed how to replace the inlet fill hose/water inlet a couple of times. The repair was exactly as shown. No trouble at all.
Poor seal on old gasket caused water to leak during dishwasher operation.
I simply pulled out the old gasket and pushed the new one in with my fingers. I had to trim about an inch off the length with a utility knife. The seal is nice and tight now and we have no more water leakage.
Needed to replace whole soap dispenser unit. Had to take front door apart cause the hex screws are on the inside. (10 Screws) then doors falls off onto floor if not careful. Spring loaded inner door wants to go up and outside door wants to fall off pulling on wiring. Unplug wiring to solinoid,(plug has locking release lever that needs to be pulled on) remove 6 hex screws, and dispenser comes out. Install new unit with 6 screws, plug in, and get help holding door parts together while installing the 10 screws. You are now finished. Pros are you get the complete unit, and not a bunch of parts. Cons are no diagrams or instructions/no new 6 hex head screws-reuse old ones. . . . . . Do not use soap powder/causes damage to latch parts/use only liquid soaps. . .
I watched the video and this was the easiest repair ever. Took longer to disconnect and reinstall than it did to change out the pump. Highly recommended watching the video
Unscrewed the top of the dishwasher from the counter top and slid the appliance out part way in order to reach the door spring. I loosened he spring from the bracket then slid the sleeve over the bracket. I reattached the spring to the bracket, slid the dishwasher back in and screwed it to the top just like it was prior to removal. Easy as pie.
Drain Pump was giving off a burning smell. When I pulled the dishwasher out it had some light smoke coming from the Drain Pump
Shut the power to the dishwasher off. Pulled unit out from under the counter top and raised the left hand side up for easy access. Disconnected the wiring, undid the clips, turned counter clockwise and removed. Reversed the order for installation and Connected the power. Ran several cycles successfully. Problem fixed. Burnt out water pump. Good as new if not better so far. Easy item search, Fast Shipping, Quality Part, Fair Pricing. Thank You Partselect.com
removed screws holding dishwasher to counter top,raised leveling pads,pulled dishwasher out, unplugged wiring,removed hold down nuts from inside dishwasher and installed new heater element, this was all easy the hard part was finding the code to reset the dishwasher there was no paperwork inside the dishwasher although there was an empty plastic holder.The code that worked for my model was with the door open to push the normal wash button then the high temp button three times as fast as you can within four seconds then close the door. It worked and reset the dishwasher which ran a short cycle then shut down as normal and is now working fine.After doing this select the beverage of your choice and relax. Hope this helps someone.
Remove upper tray and spray arm. Remove two screws retaining pipe for upper spray arm and overhead. Unscrew retainer on top of lower spray arm and remove. Gently rotate the upper feed pipe clockwise until pipe can be removed from lower pipe. You may then remove the lower pipe and bearing housing where the seal is. Reverse order for reassembly. I also replaced upper spray arm bushing. Very simple, remove one screw and the arm will come out.