Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Removed oven door and the 3 screws holding the bottom door trim. Attached new trim piece and reinstalled oven door. Entire job took less than 5 minutes.
My oven was assembled at the factory with half a hinge in left side ( no giant spring assembly) and in 15 months the right side hinge twisted and collapsed from bearing all the weight. First I thought I was only dealing with one bad hinge, and took the screws out of one side of door only and replaced hinge and was done in five minutes. Watched YouTube videos which were great and did the repair . Then I noticed the other hinge had no tension on it and did a complete disassembly of door and compared hinges and discovered the other shoddy assembly. I recommend you try to replace one hinge at a time. Take out screws on one side and finagle hinge into place. I did not do this and it took a long time. Rated repair difficulty due to several parts of oven door need to be aligned correctly to get the screws back in. Getting one side aligned caused the other side to become mis-aligned. Not rocket science but requires a lot of patience as you will redo it many times. I screwed the new hinges/steel channels they sit in into the inner door to help reduce the number of moving parts. Then aligned and secured door parts. I cut a 6” piece of straight wire from a coat hanger and stuck it through the screw holes to line them up. Worked very well, and after door was screwed together then I finally screwed the hinges to the outer door.
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Stove top wouldn't come on. Oven couldn't go higher than low heat
Had a technician from Home Advisor to check the problem out with my Whirlpool Double oven(1 1/2 old). Paid $60 to find the problem. According to the technician problem was control board and cost of labor and parts $465.00 Jumped on Part Select website, placed a question with my stove problem through the chat. Immediately they answered my question and told me the problem was the Terminal Block. Cost of part and shipping $25.00. Replaced it myself and everything works fine. Thank you, Thank you Part Select for your help and honesty.
First I disconnected the power, removed the screw that hold the element in place. Then, I pulled the element out and cut the two wires. I connected the two wires with the new element as the instruction provided by Part Select. I put the element back and screwed it in place. I plugged in the power and turned on the burner. It works. It is really easy to repair.
Pulled the dial off, unscrew two screws. Pull the switch out from the back. Disconnect the wires from the old switch and connect to the new switch one by one. Set the new switch in place. Sctew the two screws in to hold the switch in place. Push on the dial.
The oven and ranges would not heat up and an F9 error was displaying on the Oven Screen.
So, the F9 error indicates a electrical power issue. First I pulled the oven out and verified I had 240 volts at my outlet.
Then I removed the fire panel over the terminal block and the issue was apparent. The nuts on the terminal block were corroded. This had cause the resistance in the connection to raise and burn up the wire to my oven plug at the terminal block.
I removed the whole back panel and everything else seemed OK visually.
1. I go new connectors for the oven plug, stripped the wires, and crimped on the new connectors.
2. The terminal block DOES NOT come with the nuts to connect the wire to the terminal block. Mine were so corroded they had to be replaced. So I went and purchased the correct ones and installed the terminal block and reconnected all the wires.
3. I applied some dielectric grease to the connections through out the process of reinstalling to prevent it from happening in the future.