Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Water leaked when the washer tub filled.
I removed two screws near the bottom of the front panel and removed the panel by pulling the bottom away from the machine. Inside, I removed two cap screws, one under each front corner of the top panel. The top panel is hinged at the rear. I lifted the top panel from the front, rotated it to the rear and leaned it against the wall behind the machine. It was not necessary to disconnect any wiring. The "U" shaped water injector hose connects to the washer water source with a hose clamp and has a grommet-like end that fits in a round hole in the top of the tub. The hose had cracked and was leaking where it connected to the tub. The new injector hose was a direct replacement and was easy to install.
Water won't drain, slight water leak, unbalances frequently
My washer was sitting in a safety drain pan which made it difficult to work on due to the height of the pan walls. Managed to tilt it back and support on blocks well enough to access underside. Found two of the four leveling feet had fallen off, which was the ultimate cause of the problems from the cumulative effect of running unbalanced over time. Reinstalled these feet and had to remove rust to do so. I added two more nuts to the front feet to hold the adjustment tight. After adjusting to level, washer ran great and was no longer prone to unbalance. Procedure: Remove front panel- two lower screws and pry/pull off. Remove hoses at pump. Remove 3 mounting screws from pump. Remove belt from pump pulley. Push motor towards center of washer to release tension from other belt, and remove belt. Replace with new belt. Replaced old drain hose to pump and replaced all hose clamps with new. Install pump, replace pump belt. Level the washer. Replace front panel. Take the opportunity while the washer is open to clean out the dust from inside!
The repair itself is fairly simple. However, being 65 years old getting the new valve back into the back opening of the washer and screwed in was a challenge. The clamp on the water connector hose broke and I had to drive to the store to replace it. You may want to consider giving a heads-ups option of ordering hose clamps to DIYers, when you go to order. Also, the instructions that came with the part was not totally accurate. I had to rotate the cylinders outward to connect to the electrical points. But, my machine is pretty old and that may be why. Otherwise, I am very pleased with how quick I received the part and it was exactly what I ordered. My washing machine is back in business. Thank you
Removed front door from washer lifted front of washer off floor and removed belt’s put washer back on floor Removed motor and slide Cleaned and replaced slides and greased put back in washer secured Then lifted front of washer back up replaced new belts and started the washer up worked great put front of washer back on done Great instructions that came with parts
well i first put on 2 new belts because they were worn and smoking. the new belts did not fix the problem. you suggested putting in a new pulley. it went against my better judgement that the pulley was defective. well i put in the new pulley and now the real problem has surfaced. the transmission is not working. now i want to order a new tranny and low and behold it is no longer available. well why did you sell me a $99 pulley when that was not the next part to change after the belts were replaced. now i have a new pulley on a washer that is going to the recycle center as metal trash. well on my part i will reward maytag by buying a ge washer now. plus i will not count on using you as my parts supplier.
Cold water keep entering the tub, I had to shut off the supply line.
I order a water inlet valve from this site It was the best buy around. The email from the site part came with a video how to change it. It was a 15 minute job. One 5/16 nut driver to remove the inlet valve and pliers to remove the hoes from the valve. Easy off easy on.
Washer was making a loud clunk-clunk-clunk going into spin cycle.
Found main drive belt had a big chunk out of it. Both belts were worn and "gummy". Replaced both belts with belt kit 12112425; no tools needed -- belts are replaced from the bottom. Just tip the washer back to the wall, and there are the belts.. Installation time 5 minutes.
took front panel off had 2 screws, propped up washer in front, took belts off with hands and put new ones on in reverse order One belt was badly cracked. I am 77 year old female, if I can do it, anybody can. great service on getting belts too. Thank you
I tipped the washing machine (somewhat tricky since it sits under the dryer) and saw the broken belt. Went online, found the belt I needed, bought the set of two belts since I figured it would probably be a good idea to change both belts at the same time. After a few days I had the belts in hand; it took more time to jockey the machine back into place than it did to attach the belts. No tools necessary; the washer parts are on a spring. I did need a screwdriver, however, just to re-attach the washer's front panel.
A friend said the cause was probably a belt. On Google we checked the washer model number which took us to your site. We looked at the videos on how to do the repairs, and so ordered a drive belt and pump belt. They arrived in two days. My husband is 84-years-old, I'm 83 -- difficult for us to lift the machine to tilt it. Experimenting with fulcrum and lever, we managed -- that's what took so long. After watching the videos again, I laid on the floor and was able to apply the belts. Washer works great!
Washer was not draining completely & at times a small amount of water would leak from under the washer.
Followed the instructions on-line. Pulled the washer out from the wall, tipped it back about 45 deg. & removed the two philips screws as the base of the front of the washer.Removed the old belts which showed little wear, disconnected the hoses from the pump. Replaced the pump which was held in by only 3 nut-head screws, attached the belts & adjusted the tesnion as described on the website.
Repair not that complicated. Remove front, lean top back, remove agitator, remove special nut, remove inner tub, remove seal. Clean shaft and seal surfaces. It is highly recommended to the spanner wrench to remove the special nut. It appears one can do it with a punch and hammer, but the nut is too tight, and corroded from years of water exposure. I believe part number is TJ90TB123A, about $15. Watch the video on this web site, very good.
