A502S Maytag Washer - Instructions

I followed the video provided. The video was very clear and helpful.

My wife did the repair. Went on your website and watch the video on how to replace the switch and she was able to do it herself. I didn't mind at all. Saved $75.00 service charge.

followed video from your website. Nut does not come off as easy as your video shows.

watched video, ordered parts, parts arrived fast in two days, watched video again, Repaired washer saved money

Remove front panel removed two screws holding top down, then removed plastic tube cover, removed balancer to make more room to work. Next removed set screw holding dasher, next remove spanner nut that held inner tube shield. Tthen lifted inner tube out of washer, now I removed the stem hold down and seal important clean area where seal touches the tube nowuse little water to wet new seal pt new seal ln careful not to damage simply reverse removal step and put the unit back together

contacted Justanswer.com with description. Expert defined problem, identified part need and gave us link to your website. Rapid arrival of part, but we took a couple of weeks to get around to it as the washer was operational, just noisy. Website video of how to do repair was invaluable. Watched prior to starting the job and checked video again during repair to verify understanding. Wonderful to be independent of the vagaries of appliance repair. I would recommend Justanswer and PartSelect to anyone!

Exactly as shown in your provided video from You Tube. What a life saver. The description of needed tools, and the fact that the main nuts securing the tub were REVERSE thread! I would not have suspected that and probably would still be beating on them, tightening them rather than loosening them!It is worth the price to purchase the spanner wrench (correct style), used to remove those tub nuts. Thanks for the great service and the video. Well done!

I found on youtube that there are directions to repair. Dryer problems are usually one of three things, the door switch being one of them. i checked this last (should have been first). ordered the part( about 65% off sear's cost) and it came in one day! It went on really easy as long as you knew from repair video how to access inside. almost spent $400.00 on a new one.

The repair went well.I had to replace the seal under the tub.The video was the key to my success,I did not have a spanner wrench,I don't think it would have helped anyway,The nut was corroded I had to drill holes and chisel it apart after that it was no problem.

I did an internet search for a leaking washer and came across this web site.I looked under my washer model and it showed the repair parts plus it has a video of a repairman doing the job.The video was none the less the best help I could ever imagine.Tools needed and how to do the job a step at a time.The parts came to my door in two days via regular shipping method.I also purchased the special SPANNER WRENCH on eBay for about 10 bucks and it showed up the same day as my parts.The job took me about a hour and now my washer works like it should with no leaks.Thanks to Parts Select I highly recommend this site and their my new lifesaver. Ciao, Steve M

After watching the repair on the video, I was confident that I could complete this job. The only tool I did not have was the special wrench for the retaining nut. I would recommend changing out the Bearing along with the seal. Due to the proximity of the seal, the bearing will most likely fail about the same time. The inner and outer tubs in my machine needed a thorough cleaning unlike the pre-cleaned demonstration washer in the video. A cheap plastic putty knife was great tool to scrape off the 14 years of detergent and lime sludge on the tubs. Allow yourself additional time to get everything clean as you disassemble the washer. The only snag I ran into was removing the corroded aluminum retaining nut. A cold chisel and hammer cut it off without much problem and a new nut was supplied with the kit. My old Maytag washer is now running like a champ and with no leaks.

Replacing both belts was very easy. The belts slipped off the pulleys with no tools required. It took less than ten minutes to change them including tilting the washer back for access. The only reason to take the front cover of the cabinet off was to check belt tension and vacuum out the interior.

Once i figured out it would not drain i pulled the front panel off and pulled all the drain hoses off to be sure nothing was clogged there or in the pump itself. It was not so then i checked the drive belt and it was ok. Next i pulled off the drain pump and everything looked to be ok, it was not froze up and it would spin just fine. I got a screwdriver and held the splines inside the pump while trying to turn the pulley and thats when i found that the propeller was spinning on the shaft and under a load would only spin the shaft and not the propeller inside the pump. Got online ordered new pump and it works great now.

I was impressed with the fast time the part was delivered. The price was good too. The installation video and instructions did not match my dryer but it was helpful to some extent. The video and instructions being different was not ya'll's fault because of the age of the dryer. It took me so long to change the switch was because of the location and design of the switch. I got it though.

I watched the online video that was supplied when I ordered the part and it made all the difference in a successful repair. Thank you for having such a complete solution!