A15CT Maytag Washer - Instructions

I followed the step by step instructions on the video and it worked to a (T). You guys are the best. Thank you for all your help. Sincerely Eddie .

I am not going to describe the repair. The video that Part Select has on their website is exactly how our repair went. Very simple. This is the second time we have used Part Select. They have saved us a lot of money on repairmen or new purchases. I would definitely use them in the future. The videos are so easy to follow anybody can make the repairs. Also, the delivery company not only misdelivered the part but, they damaged it. When I called Part Select about the part being damaged, they immediately sent out a new part without any questions. Why aren't all companies this awesome?!

First I looked it up on the computer and clicked on Part Select's page and it came up with the part needed and then I watched the video on installing the part. It was easy to follow their instructions and the repair was made. I was so pleased with everything I ran across a man in the hardware store this morning and he was having cloths dryer trouble that I told him to just click on your site and the rest would be easy. He said he would do that. In fact I took the Wife out to dinner on just part of what money you saved me. Thanks, Harold

I watched the video and everthing went pretty well. The only problem I had was removing the Clamp Nut. My Washer is more than 10yrs. old so there is a lot of water and lime build up. I use a Cole Chisel and a Ball Pen Hammer to break the Clamp Nut. Because you can dispose of it anyway a new Clamp Nut comes with your Mounting Stem/Tub Seal Kit. The Tub wrench comes in handy for removing the Mounting Stem and to reseat the Mounting Stem. You are also going to need the Tub Wrench for reseating the Clamp Nut. You can order a Tub Wrench online there are various web sites.

Repair was very easy. I watched the video once and followed all the instructions to replace the water inlet valve, injector valve and nozzle. If I see it done once, I can do the repair. I was very impressed with PartSelect's web site, instructions and video. I'm glad my wife found you on the web. Will do business with you again.

Removed access panel on back of machine to remove Air Tube where it connects to wash basin. Removed control panel cover on top of machine and front panel of machine so top could be lifted for easier access to the point where Air Tube plugs in to water level selector switch. Tube is attached at both ends via spring clips. Replaced tube; problem solved. As a note, the old tube was clogged, and once cleaned, the machine functioned normally again. I had already ordered the replacement so I installed it in place of the old tube when it arrived. The new tube is significantly longer but functions perfectly.

I got all of my repair information from your website. I started with 'Maytag washer leaks' and found out that, statistically, the rubber injector valve was the first most likely leak source. Then, to check if this was actually the leak, I lifted the top of the machine during the fill cycle, and watched the water spritzing from the housing that enclosed the Rubber Injector Valve. Next, I watched one of your repair videos associated with replacing the valve. Next, I ordered the part from you. When it came, I installed it. The whole process, from beginning to end, was very good.

Removed the old one installed the new one

Replaced the pump. The front panel screws were rusty. I also replaced the belts at the same time. The repair video told me just what to do. I wouldn't have known about the belt tension otherwise.

Everything basically went as planned. Putting the belts on was a breeze, but I had trouble getting on the screws that anchored the pump in. The pulley didn't allow access for a nut driver or socket, even with a universal, there still wasn't enough clearance. I went back and forth between using a screw driver in the end of a socket and using the socket on the end of a tiny breaker bar. It wasn't bad, just took a little patience. Everything works like a champ now.

Same technique as the PartSelect video, except the result leaked to the outside at the outlet port because the two halves of the mold that made it were slightly misaligned, and there were two steps, one on each side of the fitting. Filed the steps away, and used Evinrude gasket sealant to make sure it wouldn't leak, and it didn't.

My husband did the repair. Since he owned a laundry quite a few years ago, he knew what he was doing. After hooking everything back up, the cold water was coming in hot. When hooking up the hoses, he had hooked the cold into the top intake. After watching the online video, he realized that the plate that was to be installed over the hoses, on the back of the washer, clearly stated "H" on top and "C" on the bottom. So we switched the position of the hoses and everything ran perfectly after that. I would suggest to ANYONE doing this repair, to watch the online video first, before starting, because it is very, very helpful.

Watched your viedo, pulled the power plug, pulled the washer away from the wall and tilted back to expose the belts. Rolled the old belts off and put the new ones on. Just be sure to put the correct belt on the pump and agitator drive as they are a bit different. Adjusted the pump belt as described in the inclosed instructions. What was strange was the same instructions was enclosed with the aggiator drive belt which appears to not be adjustable. Once adjusted put washer back in normal position, plugged in power and was ready to go. Seems to work fine now, least no complaints from the wife.

Removed washing Machine Cover. Removed old belts and then old pump. Installed New pump and then the new belts. Cleaned and vacuumed inside of washing Machine. Replaced cover. Hooked up hoses and ran the washer. Every thing worked great and water was pumped out of the washing Machine leaving the cloths spun dry and clean. Really easy job to do.

Emptied washing machine tub with a small plastic bowl into a 5 gallon bucket, finihsing up last bit of water by soaking it up with towels. I next removed front panel on washing machine by unscrewing two screws on the bottom front, left and right, to gain access to the pump. Loosened two hose clamps and detached two hoses, catching remining water from washertub. moved washer out from wall about 3 feet and tilted washer back towards wall so I could access the inderneath of washer to lossen three bolts that held pump in place. removed belt from pum to motor and examined fro glaze or wear (none detected) and then removed pum and reversed steps to install new pump, reinstalling belt faily loosly, per instructions. Tried washer to see if ssue resolved and once confirmed, replaced the front panel. Have done multiple washes since then (at least 10) and no further issues. Very economical solution (under $100) and sense of pride with fixing applianmce myself. This web page was very informative and saved me a lot of money and time. Thanks!