Models > 9119344190 > Instructions

9119344190 Kenmore Oven - Instructions

All installation instructions for 9119344190 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the oven repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 9119344190
46-60 of 304
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

broken heat element

  • Customer: Young from Oakland NJ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 1 of 1 people found this instruction helpful
It was very easy than i expect,
Just pullout the stove from the location to access rear side of stove,
unscrew 3 nuts with socket rench and disconnected wire. Opened front door of stove, unscrew 5 screwss , then pulled out broken element, replaced it with new one.
It is very very easy , Dont be affraid do it yourself.....

Broil element snapped and went on fire.

  • Customer: kathleen from broad channel NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 1 of 1 people found this instruction helpful
I could not believe how easy it was to repair my own oven! Honestly I was shocked. I pulled the oven out, unscrewed 7 screws, pulled the old element out, placed the new one in, replaced the screws and I was done. All I could think about was how much money I saved! Also, it took me about 15 minutes.

Bake Element on Oven Arced and Split

  • Customer: Lisa from The Woodlands TX
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 1 of 1 people found this instruction helpful
Instead of flipping circuit breaker, we pulled the oven away from the wall and unplugged it. Used socket wrench to loosen screws of bracket holding old element onto the back oven wall, then gently pulled element until connecting wires appeared. Removed the 'clips' attached to the old element prongs and discarded old element. Reattached the 'clips' to new element prongs, then gently pushed prongs into back into oven wall until the bracket was flush with the wall. Used socket wrench to screw and tighten the bracket into place. Plugged in the oven and tested the new element to make sure it worked. The whole process took only a few minutes.....it took longer to clean the oven before installing the new element.

Oven door hinge rollers had broken.

  • Customer: Lonnie from Nipomo CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
The repair went surprisingly well! My only problem was the bottom screws needed WD40 to loosen, but otherwise the parts went in easily.

baking element arced and burned out

  • Customer: Norman Levitz from Manchester Center VT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 1 of 1 people found this instruction helpful
Removed oven racks and took the opportunity to clean my oven. Then removed the two hex head nuts holding the burner assembly in place. I slid out the burner (very slowly) hoping the connectors were intact and that there was enough lead wire to make for an easy repair. Yes... there were 2 inches of lead wire. It took a couple of minutes to swap out the parts and... success!
Don't forget to turn off the circuit breaker before starting repairs.

Oven no longer heated except for Broil element

  • Customer: Derrick from Ypsilanti MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 1 of 1 people found this instruction helpful
1)Unscrewed old baking element from wall of oven
2)Detached old baking element from wires
3)Attached new baking element to wires
4)Screwed new baking element to wall of oven
5)Turned on oven

oven coil caught on fire and broke in half!

  • Customer: Cynthia from Houston TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Wrench(Adjustable)
  • 2 of 4 people found this instruction helpful
I turned off the main power! Then unscrewed the back cover unhooked the wires and unscrewed the coil inside of the oven and pulled it out. My 10yr old son and I measured it and went online to order the part. I first did go into BestBuy and they didn't have the part (But they tried to sale me a new oven!) LOL Now who said a newly divorced mom couldn't fix her own oven! My Tech Support skills came in handy! Women Rock! LOL

hinge roller broke

  • Customer: Allen from McCalla AL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 1 people found this instruction helpful
first open oven door a couple inches and slide door up off hinges, then removed storage drawer to gain access to hinge spring, remove hinge spring with pliers noting which hole spring was attached in.then remove three screws from hinge and installed new hinge put three screws in attached spring back and put storage drawer in and oven door back on.

The bake element was burnt out.

  • Customer: Linda from Fort Collins CO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 1 of 1 people found this instruction helpful
It took a nutdriver to remove two nuts. The defective element was removed and the replacement installed. It works great!

insulation replacement due to cooking oil spillage

  • Customer: Michael from Kiln MS
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 1 people found this instruction helpful
raised hood, removed four screws that hold the top plate.
placed in new insulation and replace top plate.
ran oven at 500 degrees for 20 minutes. all OK.

Tenant broke bake element

  • Customer: John from Muncie IN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 1 of 1 people found this instruction helpful
Removed the two screws, pulled out old element, installed new element, and reinstalled screws.

No heat lower bake unit / Broiler unit heats ok

  • Customer: Richard L. from Clear Spring MD
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 1 of 1 people found this instruction helpful
Safety first: Turn range circuit breaker to off position. Turn a surface unit [burner] to the on position ,if no light exists power has been removed. Turn surface unit to off position. To remove bake unit. With a 1/4 socket driver remove two self tapping screws and gently pull out on the bake unit until you can access the slide on terninals. Careful lenth of wire is limited. Remove slide on terminals two each [2] . Install new bake unit in reverse order . Restore power

The old heating erlement basically melted and broke in two places

  • Customer: Coleen from Danville IN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
I unscrewed the two screws inside the oven, then i pulled the oven away from the wall and unscrewed the protective shield, and undid the wiring. Then i removed the element. Once the new one arrived, i pretty much just did the same thing in reverse. vwa-lah... fixed!

Over door would not open fully; light was always on

  • Customer: Fareed from Randolph NJ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
Slid off the oven door and loosened the hinge assembly. Removed the storage drawer to unhook the spring and then took off the old hinge assembly.

Inserted the spring into the new hinge assembly and then installed it - just tightened the screws. Hooked the spring into the lower point. Slid in the oven door and tested it so that is opened/closed easily. Cleaned under the oven while the storage drawer was out.

We can now bake bread, pizza, etc. What a relief.

burnt element

  • Customer: Brian from Iron River MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 1 of 1 people found this instruction helpful
.g. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...)
All Instructions for the 9119344190
46-60 of 304