Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
heating element in oven
I first pulled the stove away from the wall to unplug and look from the rear. Look at the wiring from the back (you may have to remove 2 screws and the plate that covers the wiring) and take a picture of it if you can with your smart phone - this way when you go to put it back you have a reference. I then removed the oven racks and the 2 little bolts holding the element in place. Wiggle it toward you slowly so the wires don't pull off. It's easier if you use needle nose pliers to get the fittings off, if its hard wiggle the fitting it will come off. I put the connections on the new element and squeezed them tight not to move. I did put a small piece of electrical tape on the connection ends for my piece of mind. Screw it back in and, plug it in and turn on. If the element starts to glow your done, put the cover back on over the wires and slide it back in place. If your kind of handy you can do it.
Replaced the outlet the one of the top burners on top of my stove, it went very well.
I followed the instructions on the video, the only thing they left out is where the wires go through to the back of the stove being that there are sharp edges. A role of glass tape would have been handy to replace the old tape. Thanks for asking, I hope this helps someone else.
Unplugged the stove from wall, pulled out oven racks. Unscrewed 2 screws that attached the burner to the oven. Pulled the two wires off, be careful not to let them go back into or behind the oven wall, then you would need to take the back center panel off and push them back through. But I bent the wire enough when taking them off to make sure they rested on the inside of the oven wall, got the new burner attached it to the two wires, screwed it back in the oven wall and I was done. Plugged it back in and works beautifully. Whole thing took maybe 15 minutes 30 minutes tops.
Old drip bowls were badly tarnished . . . shine could not be restored.
1) Make sure unit switches are turned off. 2) Lift Calrod unit up and pull it from electrical receptacle. 3) Withdraw Calrod unit from old bowl. 4) Insert Calrod unit through large hole in new bowl. 5) Push Calrod electrical connectors into receptacle under range top. 6) Seat Calrod unit on bowl rim and insert the assembled Calrod unit and bowl into the hole in the range top.
I unhooked the main power cord, unhooked the worn out block terminal cut the tape that was holding all the wires together. Removed the back panel and followed the wires unhooked the 2 wires and installed the new block terminal. Tied all the wires back, attached the back panel and plugged the power cord back into the outlet. i tested the burner to see if it was working. The burner is working great, instructions were easy to follow and my wife is happy. Thank you
Remove screws on bake element and on back cover to wires (unplug unit first) remove terminal ends , replace element put cover back on and screw in element hold down screws.
Had to move the range out of its little cubby hole in the kitchen so that I could have access to the back of the range. This process probably took the longest. After that it was a piece of cake. Took about 15 minutes to complete the job. So easy, eve a caveman could do it.
To 80 year old (young) brothers worked together. One hooked the wires the other one plug it in. Very simple install.. Neither one knows anything about electricity. Thank you for your service.
I had read some of the other comments about the repairs. The one that I found most useful was the one describing how short the connector was once they are removed. That isn't a joke about 3/4". My sujestion is to have tape and tape them to the back of the oven so as to not to loose them in the insulation. Once that was removed and reconnected the oven worked again like new. Even the most novice of people will find it a breeze.
oven not hot enough,would not shut off and had bright red spot element
unplugged stove-removed cover in back of stove-unplugged element-inside oven removed two screws-removed element. reverse procedure to install. took about twenty minutes. wife happy again. parts came in two days. I could not believe how fast it came. Thank You very much! Jim Jewkes
Unplugged oven.I opened up back of oven the connectors to the heating element were showing. disconnected the wires(they just pulled off)went inside oven took the 2 screws out and pulled old heating element out. Put new element in and fastened it with the 2 screws. Went to back of oven slid the connectors together.Put back of oven back on plugged it in and started the oven. It worked
Took out the nuts that held the old element, removed it, put in new element with tightened nuts...and it didn't work. We took off the plate on the back of the stove, found the element contacts protruding through, attached them to the wire connectors that were close by, and it DID work. We were thankful it turned out to be easy!