Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
The top is all glass so I took my time. There was about 12 screws and double sided tape. A lock washer holding the igniter on. It also gave me a chance to clean the hard to get to places. Your price was almost half of what a suppier here and getting it would have been 2 weeks compared to your 48 hours to my door. Thanks again
F2 error code when oven was set at a higher temperature.
I pretty much followed the youtube video posted under the part that I needed. Turned off electricity to that area of the house. Unplugged stove. Took out the old sensor, pushed new sensor cord through the back hole. I did put a small amount of tape,so I could pull it through from the back better. It was impossible to get the clip disconnected in the back and the new clip didn't match up correctly anyway. Ended up having to cut the wires and strip them. I twisted them together and put on the ceramic wire nuts on. Reversed ever thing I did and F3 appeared. Looked that code up on internet. It was from an open or shorted oven. Suggested I check the connections. Pulled stove out again, unscrewed caps on wires and noticed the sensor's wire had another cloth type coating on it. I gentle cut that off, twisted and capped wires again. Plugged in oven, turn on electricity, and tried out stove. Everything is working just fine. Everything took a little longer because this was first time doing this type of repair.
Easy Repair. Remove the storage draw under the oven. It lifts out. Lift oven door off of hinges. Remove 3 screws & unhook the spring. Reverse the procedure with the new hinge. Good as new.
After reading the other DIY's directions, we explored how to remove oven door. When the part came in, my sister who was visiting, removed the oven door (30seconds), removed bottom drawer (30 seconds), noted where spring was attached, took off screws and spring, installed new hinge with roller, took a minute to decide if the new hinge came through the back or the front (front), she reattached the spring and screws. Put door back on and then struggles to put the drawer back into place. Total time less than 5 mintues, most time spent on returning bottom drawer to its home. Thanks part select for helping me not burn my self every time I try and get food out of the oven!!! I open the oven door all the way and am so delighted!!
Burner would take 10-15 seconds to ignite due to no gas flowing
Removed front oven door, pull out bottom drawer and top burner glass panel to reduce weight. Pulled out from cabinet, shut off gas, removed gas line, removed two output gas lines from gas regulator, removed gas regulator, removed input pipe fitting from old gas regulator and installed it on new regulator using pipe compound on threads, installed gas regulator on stove, attached two output gas lines to new gas valve, attached gas line, checked for leaks, and then installed Top, front door and lower drawer, done. 2-3 hours.
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable), Wrench set
1 of 3 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door was hard to open
After reading other stories, I knew enough to slide the lower drawer out and take off the spring. 30 second job. I did not realize that range doors slide vertically off the hinge, did that in about 2 mins. Put the new hinge on in 2 mins (3 Screws). Slid the door back on and done. Works like a champ. My wife has her eye on new stainless appliances. Sadly, she'll have to wait a while longer.
First I removed the oven door from the support hinges. Next I pulled the bottom pan drawer out to get to the tension spring. I released the tension from the hinge, unscrewed three screws that held the hinge in place. From there I replaced the hinge put all components back in place and did it all under 20 mins. The part was received with in 3 days from PartSelect so I was very satisisfied with the service and ease of repair.
the broiler would light once in awhile and it appeared that the igniter was working. But it wouldn't let enough current through to open the gas valve. The nuts holding it on broke off but drilling them out and replacing with two sheet metal screws worked ok. Don't know how that will hold up to the heat though. The wiring was easy to connect ( wire nuts) but the lead wires from the stove are not that long so all the operation had to be done way in the back of the oven enclosure.