7MMGL6741TW1 Dryer - Instructions

I replaced the two coils that regulate the gas to turn on and the other to hold open to burn, unplug two connections and remove 2 screws and then replace the coils less then 5 minutes to do this,

Follow the instructions contained in the kit along with the excellent referenced how to video on YouTube. Will certainly go to PartSelect for all my future appliance repairs.

Igniter would glow and flame would burn for about 30 seconds then a rattling noise would start and the flame would go out. Replaced the coil and all is well. Very simple and inexpensive. One of the easiest repairs I've ever done. Video was very helpful.

Thousand dollars for a new dryer or twenty bucks for a new belt. Thank-you parts select. Ordering was easy and the instructions were bang on!

Both washer and dryer always worked perfectly. Suddenly, dryer wasn’t drying laundry properly. Problem... no heat. Cheapest price I could find calling for appliance service was about $160 to replace coil set but no one would tell me this would fix the problem. This was after calling a number of repair firms and trying to get a somewhat close estimate of what my problem was and what the repair cost. Not knowing, I might have just paid the $160 but what turned me off was having a service call fee of anywhere from $50-$80 with no one willing to tell me what the problem might most likely be before coming out or give me an estimate over the phone other than a range of $160 - $275. I just did not want to have someone come out for $50 -$80 and tell me that I needed to spend $275 and still owe them the service call even if I did not agree.
Found diagnostic and repair instructions help on line. The diagnostic information indicated a high probability, roughly 50%, that replacing the coil set would solve the problem and found the coil set cost $19.21 plus shipping, so I ordered the coil kit for total of $26.70. Note... I am a 71 year old amateur never having worked as a repairman of any kind except for my own needs.
The repair itself took less than 30 minutes start to finish and was one of the most straight forward, glitch free, easy repairs I have ever done. This is a gas dryer but still uses 110 power so I unplugged the 110 power cord from outlet. Followed suggested guidance on opening the dryer cabinet from the front and presto, the coil set I needed to replace was immediately right in front with easy access. Removed 2 screws for the hold-down bracket, slipped off both coils, one at a time, removing the wiring connection for each coil and then reconnecting to each new coil before slipping each new coil back into place and reattaching the hold down bracket. Reinstalled the dryer door and cabinet front in reverse order from taking off... 4 screws total. Plugged in the 110 power cord and put in a damp load of freshly washed laundry. Presto... 30 minutes later... dry laundry. Note... could do the same repair again in half the time since I took it slow and careful 1st time and also took time to remove dust before completing repair. I like things to look like new inside and out and it did when I was done. $26.70 and good as new. Why I didn't spend $160 - $275 is pretty obvious now.

I watched the video online in the order section. then just did it after we received the repair kit.

In accordance with supplied video and instructions. Special note - watch out for sharp edges on the dryer panels!

We only had to tilt the dryer enough to be able to screw the leveling leg in place.The only hard part was holding the dryer steady to screw in the leveling foot.

Following the step by step instructions it took longer to clean the old lint out of the bottom of the dryer than to perform the entire repair.The maintenance kit came complete with every moving part(except the motor and drum)and now it runs very quietly.I am all thumbs when it comes to tools but this was very simple.

Removed 2 screws at filter vent on top of dryer Remove screen. Take screwdriver & pry up lid at 2 front corners. Lift lid. 2 more screws inside top front corners.Remove screws. remove front panel.wrap belt around tub. Take cup or can to hold tub in place level.Thread belt around tentioner pulley & motor shaft Look at directions very closely to figure out how to thread belt. read at least 5 times.LOL Reinstall & you are through.PS you can see where old belt rode so try to line up as close to track as possible. Guy

You have to disassemble the dryer. I looked up how to on youtube.com. I am grateful that people take the time to record the steps in which to do just about anything. Disassembled and ordered motor and fan, damaged fan taking it off, got it in in just a couple of days, installed motor, fan and drum, tested before complete assembly. Works great. Thanks

Kit arrived with all the parts required and with detailed instructions. LOL... the very specialized tool you will need to dis-assemble the dryer? A PUTTY KNIFE. All in all, aside from the top of the dryer slamming shut without warning and scaring the pants off me, this was a relatively easy repair from a technical level. Only real difficult thing was removing and then restoring the drum and that was more due to clearance than actually being difficult. Make sure once you're finished to LEVEL THE DRYER. That makes a HUGE difference!!!!!

Followed Directions included with Kit. Directions were right on. Have done other Range and Drier conversions in the past.

replaced belt

Watched video on the website and saw how easy it was so ordered the part. Part arrived quickly and had dryer up and running within 15 minutes. Good part good price and good intructional video