Models > 7MMGL6741TW1

7MMGL6741TW1 Maytag Dryer - Overview

Get Parts and Repair Help for 7MMGL6741TW1

If you know the dryer repair part you need, you can browse the list of all parts on the 7MMGL6741TW1, or you can search by name or part description. You can also find your part by where it is located on the 7MMGL6741TW1 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for 7MMGL6741TW1 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$14.08

Multi Rib Belt - 92-1/4"

This dryer drum belt has four ridges, three grooves and is 1/4" wide.

$16.53

'M' Series New Style Coil Kit

This gas dryer ignition coil set comes with two ignition coils: one three terminal Boost/Hold coil, and one two terminal secondary coil.

$18.41

Door Switch - 3 Wire

A door switch is a simple on/off mechanism that prohibits the dryer from operating when the door is open.

$37.37

Igniter Kit

This silicone carbide igniter with ceramic holder kit includes the 3" flat igniter, bracket, 5" wire leads, and the plug. Able to replace both round and flat igniters, this kit is used for many gas clothes dryers.

$10.77

Door Catch Kit

This kit comes in two pieces: the catch and the clip.

$30.24

Radiant Flame Sensor

This part senses the flame for heat allowing the gas valve to open.

$3.66

Leveling Foot

Sold individually.

$88.21

Drive Motor with Pulley

This motor fits most Whirlpool incorporated dryer brands before 1996. NOTE: Pulley is NOT available separately.

$4.11

RING

$26.71

SCREEN

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

dryer would not turn off with door open

  • Customer: RICHARD from NORCROSS GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 384 of 386 people found this instruction helpful
pryed dryer top open and opened front door.. unscrewed the 2 retaining screws. pulled old switch from the wiring harness.
put new switch in place and replaced the retaining screws.
put new switch wire plug into the wiring harness. before closing top, checked door switch function with dryer on.
dryer cut off when door open and when close... read more

Dryer wouldn't turn on b/c door switch broken

  • Customer: April from Xenia OH
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 280 of 350 people found this instruction helpful
It was simple once I figured out what to do:). I removed the 2 screws on the top of the dryer... they were a bit hard to find. Even with the other descriptions on this site. I was removing things I didn't need to. The 2 screws you need to remove are under the LINT COLLECTOR LID. Remove those 2 screws & lift the lid... it will be tight at first. the fro... read more

Dryer ran but would not heat

  • Customer: Gary from Haverhill NH
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 161 of 182 people found this instruction helpful
PartSelect showed seven different possibilities why the dryer wouldn't heat. I removed the two screws to remove the bottom panel and turned the dryer on and noticed that the heating element that ignites the gas was working fine. This meant that it was not getting gas so it could be the gas valve or one of the two gas valve coils which are located on top of t... read more