7MMGE9959TW0 Maytag Dryer - Instructions

I replaced the Thermal Fuse and Cycling Thermostat first, since they were listed as fixing the problem 45% of the time and 19% of the time, but the dryer still didn't heat. I then ordered and replaced the gas valve solenoids, which solved the problem (but I ended up breaking the dryer belt while re-installing the drum, so that had to be replaced too.) In hindsight, I wish I would have ordered all four parts up front and saved a bit on shipping. Installation was easy, especially with the diagrams that showed where each part would be found.

Removed rear panel screws carefully removed panel with out disconnecting wire harness located thermal fuse removed 2 screws removed the 2 wires with needle nose pliers put new thermal fuse in connected the 2 wires carefully put panel back on and tightened screws turned on power and start got heat problem fixed

First I opened the front of my dryer panel to see when the dryer was on if there was any gas flowing. I found that the ignitor was glowing , but no gas was releasing from the valve. So I figured that that is the root of the problem. I changed the old gas valves and replaced them with the new ones. It worked!! The whole process didn't take more than 30 minutes.

After trying to follow a very detailed description by another consumer, we googled our washer and found a site that showed step by step direction that took us through removing all panels and getting to the bellow easily. Not removing the proper panels, we found was making the job hard!I believe the site was applicance services...very helpful! Step by step literally!!Cost of parts through parts select reasonable.

I diagnosed the problem using the web page. It said that 60% of the people with my problem bought the Thermal Fuse. I unplugged the dryer AND cut the power at the fuse box. I used a screwdriver to remove the vent hose, a nutdriver to remove the back of the machine. The thermal fuse was right there. Removed the old one with a screwdriver, unplugged the wires from the old one and snapped on new one, and screwed it back in. Re-installed the back of the dryer and the vent hose and Whoila! It works like a champ.

This did not require a "repair", just a replacement. I want to say that the response time and ease of ordering were very good. I would not hesitate to use PartSelect again when needed. Thank you!

pulled out old lint filter. Put in new lint filter.

Repair was very easy simply used a screwdriver to remove the cracked old latch and used my fingers to insert my new latch.

At first I thought the sensor in the drum part was bad. It had some residue from something on it and looked a bit beat up. Replaced it for 30$ and had the same problem. Note: I decided to take the console panel off because I though it was necessary to get to everywhere else and I found a folded up "repairman trouble shooting guide" in the console. Don't know if this is a common place to put it but it had all the wiring and problems detailed with this dryer. It had step-by-step assessment procedures for any problem. However, I punched the sequence for the "brains" to give me a problem code and it indicated that I needed a new "user interface," a 285$ part. I must have punched it wrong because I started to read other problem descriptions and I realized, based on others, that the most likely cause was the coils that regulate the gas/heat valve. I used the "problem guide" to measure the resistance of the coils (it gives you the proper range for each) and one was outside of what it should have been so I purchased a new set of coils for $20 plus shipping. It took me 2 tries at installing the coils because the cover plate that seats the coils in place was not aligned properly the first time. This cause them to vibrate and rattle when starting up. The coils were a little different in height so I readjusted the cover bracket and seated the coils properly. No rattle and the dryer worked perfectly.

Need a short handled phillips screwdriver. Unplug dryer from socket. Remove two screws near the bottom of the front panel. Swing the panel to one side so electrical wire doesn't need disconnection. Remove two screws holding bracket over the two coils. Unplug both coils. Plug in new coils. Replace bracket. Replace front panel. Plug machine back into electrical socket. Problem solved.

I replaced both the thermal fuse and the gas valve coils, although I'm sure the problem was the coils.

Preface this by saying I'm not a good handyman. I love working with my hands, but I cannot cut straight, make angles, plumb, or do anything electric. I knew I had a gas dryer but I had to learn that it uses a burner not a coil. That said, armed with my trusty iPad, I located Part Select, watched a video or two, entered my problems into the correct fields, and made an educated guess based off of the results. Since I already had the front cover and the motor cover off the dryer and the 2 sensors were right there, I ordered both-why take the chance. I ordered Sunday evening and the parts arrived Tuesday around noon. By 1pm I was drying clothes. Feeling pretty cocky now, I'm going to try to hang gutters this weekend.

Replaced igniter

I got great advice and the know how form other's instructions. It was a really easy fix. I unplugged the dryer and turned off the gas valve. Open up the dryer by taking out the two screws securing the lint screen. Then pop off the top of the dryer by inserting a screwdriver. Disconnect the door switch and depending on model remove the two screws or bolts that keep the front panel attached. Careful, on my dryer once took the front panel off the drum fell forward. I kept it in place by wedging a small cardboard box under it. Unplug the two wires going into each of the coils. Remember which one goes where(2 prong vs 3 prong). Undue the two screws holding the bracket to the coils and remove bracket and bad coils. Put the new coils in, attach wires and bracket. Put dryer back together. Make sure to remember to plug back in door switch. I forgot and when I tried to test it wouldn't work and it got me worried that I broke it or something.

I first came to the internet to resolve what was wrong. After finding the video I thought was correct I started. I used my volt/ohm meter to check the thermal fuse as instructed on the video and that was the problem. I ordered the new thermal fuse from PartSelect late in the day and it was in my hands the next evening. With in 20 minutes the dryer was doing what it was suppose to do. The hardest part was getting the back cover of the crier off and that wasn't to bad.