7MMGD6630TQ0 Dryer - Instructions

Removed back cover,top,lower and upper front,and drum. Cleaned dust and dirt drom all of the removed parts and then removed the "lint tube". Took the tube apart to clean out dirt and lint, cleaned the lint off of the motor and blower wheel, and then removed the support wheels. Installed the "lint tube" and then the new support wheels with the new locks and then installed the new belt onto the drum. I had to support the drum in order to correctly line up the belt, and then installed the upper front panel. plugged in the power cord and started the motor to be sure everything was OK before closing up the rest of the cabinet. All was OK and the belt tracted perfectly. Installed the lower front panel, top, and the rear panel. Installed the gas connection, checked for gas leaks and installed the dryer back in place. checked operation with a batch of wet clothes and the dryer worked "better than new"!!! The instruction sheet was "spot on" for clarity and accuracy.

Opened dryer top, disconnected door wireing, took off front panel, laid dryer on back, cleaned out lint and inside, put new belt on, and put parts back together. Dryer works fine now.

Remove Filter and (2) phillip screws. Use common screw driver to pry top from cabinet. Fold top back. disconnect door switch and removed (2) screws holding front of cabinet and lift frong slightly to remove from cabinet. Remove broken belt and discard. check rollers for freedom and placed drum on rollers. guided belt through idler and around motor pulley. lift front and placed on lower hooks. Lift drum and installed (2) screws that holds front of cabinet to main cabinet. connect door switch and check drum for freedom of turn. turn drum several times to get belt to center. Closed top and replaced (2) screws that hold filter door in place. Install filter and test run dryer. Completed job in about 38 minutes.

I followed the instructions supplied with the belt. I've changed the belt before so was familiar with the repair. The toe panel clips for my model had changed so what was supplied was different than the originals. Although they, too, came with instructions, they did not fit my appliance. They were inexpensive so I scrapped them and used some self-adhesive Velcro fasteners I had in a junk box.

I replaced the Cycling thermostat. At first I thought I may have blamed the wrong part because the ohm meter read almost the same for the old and the new part. It took less than a day for the part to come probably because it came from Jacksonville. I haven't guessed how much I saved by not calling a appliance repair.

belt # 346995. part was delivered quickly. Part fit perfect, no problem. there was a video on youtube how to replace it. It took about 25 minutes from start to finish to install. works like a new one. Thanks partselect.

I had to opcn up dryer, remove drum and replace worn parts.

It was fairly easy, the comments and pics on this site were quite heplful. I just took out the screws on the lint trap and popped the top by pushing in on the clips with a putty knife. zlift the top and swing it back. I cut the old belt with a utility knife since i was replacing it and lifted out the drum. the drum wheels just pop off and on so they are really easy to replace. next I took off the old rear seal with a putty knife and put the new one on. This is a messy affair if you are not careful, I ended up with adhesive all over my hands. Next loop the new belt over the drum and replace it aligning it. You kneed someone to help you hold the drum level while you replace the belt wheel and front. Run the drum around with a putty knife under the new seal to make sure it is not tucked under anywhere. Put it all back together and you are done.

Remove the two screws holding the door and lift straight up. Remove the two screws on oppostie side. Face can now be removed by pulling straight out at the top, then lifting face up off of tabs at the bottom. The two coils are at the bottom, held in by a retaining bracket. Remove the screws that hold the bracket. Replace the coils by unplugged their wires. That's it!

The dryer belt was delivered promply, afterwards I lifted the top of the dryer and unscrewed the front panel, so it would lower. Then I watch a 5 minute video and it clearly demonstrated how to install the belt. This was my first time, so it took about 30 minutes.

changed fuse,radiant flame sensor. no help. bought a new dryer. i don't think the gas valuve was opening.everything seemed to be working properly,just no gas.

PartSelect sent the exact right part, and very quickly! YouTube showed me how to install it. The only hard part was the bulkiness of the drum, which is why I marked "a bit difficult" for the repair.

It was a fairly simple repair to perform with the dryer in place. I simply opened the bottom/front access panel to start, the door removes if you pull up after opening. Then I disconnected the two and three wire connector to the two coils. Next I removed the bracket screws that fasten the coils to the valve assembly. This was a little difficult with the screw closest, because of the small clearance and #1 sized phillips(stubby would work well.) The rear screw I managed to remove by using both a small flathead screwdriver(hex shaped shaft) and an adjustable cresent wrench. At this point, it was a simple matter of installing the new coils and the bracket, and then reconnecting the two plugs. It almost made me want to do laundry.

Slid the new lint filter into slot on top of my 26 year-old Kenmore dryer and it fit perfectly! Ordered part and received it the next day...unbelievable!! Definitely A+ service.

Parts Select said 27% chance it was the coils and 26% chance it was moisture sensor. I ordered the coils and it did not fix the problem, my luck. I have now ordered moisture sensor and the next possible part, the cycling thermostat. If one of these solve the problem I will still have much less invested than a repairman would charge.