Models > 7MMGD6630TM0 > Instructions

7MMGD6630TM0 Maytag Dryer - Instructions

All installation instructions for 7MMGD6630TM0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 7MMGD6630TM0
826-840 of 899
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Broken Belt

  • Customer: gary w from Saint Louis MO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Pop off the top , Then one screw holds each side . slide belt around drum and then preload tensioner as per instructions . Simple!

Broken Dryer belt

  • Customer: Glenn from Waterford CT
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I follow the instructions from the video sent to me with the email to tell me my new belt was shipped. Made the whole job go a easy as could be. Parts Select made fixing my dryer so simple and I also got the belt within 2 days. I recommend buying parts only from you! Glenn

Drum was not turning when the start button was pushed while morot was running

  • Customer: Philip S from Springfield VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
After I received the new belt I un-plugged the electric cord and shut off the gas supply. I pulled the dryer about 10 inches away from the wall to remove the vent duct from the back of the dryer. Used the putty knife to release the clips on bottom front panel and a screw driver to pop the front of the top at the left side and right side, removed the two Phillips head screws under the lint door, then lifted the top to the vertical position. Loosened the hex head screws at the bottom of the upper front panel (don't take them out). At the top back side of the front panel, pull off the electrical wires from the door interlock switch and pull the retainer holding the wires to the front panel (don't take the plastic clip from the wires.) Place some wood blocks to support the drum at the front of the drum. Use the nut driver to remove the two screws on the inside at the top of the front panel. Disconnect the two springs that hold the door closed. Lift the panel from the two loosened nuts at the bottom and pull it away from the drum and let the drum settle on the blocks of wood to support it. Place the new belt around the drum lining it up where the old belt left its mark around the drum with the grooved surface facing the drum. Replace the front upper panel with the door to engage to two tabs on the screws you left at the bottom. Lift the drum so that it engages with the opening in the front panel. In case where the drum had dropped too far, use the putty knife to engage the felt flange at the rear of the drum with the rear cabinet flange. Reinstall the two screws at the top that you had removed. Reconnect the two wires at the interlock switch and snap the clip with the wires to the flange of the upper front panel. Replace the door springs on the hinge extensions to the flange at the bottom of the cabinet. Set the Idler pulley assembly into the cabinet floor sliding the end tab into the slot and the two tabs fit into the holes in the floor. Pull a loop of the belt under the idler pulley and then pull it toward the motor pulley. You might use the shaft of your Phillips screw driver instead of you fingers to get it around the pulley on the motor shaft. Turn the drum by had for several complete turns to ensure that the belt lines up on the drum and that the drum isn't binding on the back or front seals. Close the top, snapping onto the top of the cabinet. Plug the dryer into the electric outlet and set the timer to Fluff Air range and push the start button with the door closed. The drum should be turning smoothly. Open the door and all should stop. Reconnect the Vent and move the dryer back to its former position. Turn gas supply on but do not start the dryer. Check for gas leaks. If you find a leak in either at connectors or the flexible connecter call a qualified contractor to replace the flex connecter. Otherwise you can then set for one of the dryer settings and push the start button and observe the burner through the lower panel to see that the igniter is lighting up and finally the gas turns on and a decent blue flam is burning in the combustion tube. Open the dryer door and the flame should cut off and the drum stop turning. You are ready to set the bottom panel. Set the panel on the two lower tabs and close it upward until the snaps lock it in position. Job Done

Broken belt

  • Customer: Christopher from Skillman NJ
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Used PartSelect instructions for routing belt & a customer's valuable guidance.

Drive belt very warn, not broken

  • Customer: Philip from Cambridge MN
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I removed screws for the lint screen - TOP. Pry up top with screw driver. Disconnected inside top front 2 screws, removed door control wires, white and blue. Lift off front of dryer. Tip dryer back about 40 degrees against wall. Remove warn belt (not broken). Relocate idler bracket on the cabinet base, follow diagram which comes with the belt package. Be very careful that the belt is NOT on the side of the idler roller. I had to do this install a second time, because I had it wrong the first time. Even though I've done this repair 5 or 6 times, there's always a first time GOOF. Not really a hard job.

Drum not turning / belt broken

  • Customer: Jill from Bangor PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I won't tell you how we did it, but I'll tell you the right way. Unplug. Remove the exhaust tubing attached to back of dryer. Pry the top up from the front and lean it against the wall. Un plug the wires attached to the front panel (remember where they go) Remove screws at top sides of front panel. "lift up" and remove. Close top. Lay machine on its back. We used a couple of 2x4's to lay it on so as not to crush the vest collar. Clean it out, including lint filter. The new belt wraps around the drum, you will see the channel about midway on drum. Feel behind the motor on the lower right side. There is a shaft with a channel for the belt. Immediately next to that is another pulley type arm with another channel for the belt. This arm moves stiffly and puts tension on the belt when installed correctly. Look at the diagram included with the new belt which shows the path of the belt. Wrap the belt, ridges against the drum and then around the motor shaft. At this point you have to physically pull the last arm out to allow the belt to wrap around the channel provided. If the belt is not twisted , the job is done. Turn the drum with your hands to make sure it is turning properly. Replace the front panel, plug in the electricals, replace the screws making sure the drum is properly centered. Stand up the dryer. Plug in and turn on dryer to make sure everything is right. Replace the exhaust tubing and set into place. Sounds like a lot of steps but I have described the whole process for you beginners. The rest of you will know already. Good Luck . Oh by the way we are 69 and 71. If we can do it, so can you

Broken belt

  • Customer: Clayton from Girard KS
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I followed video instructions. Raised the top, slipped off the front, installed the belt, aligned, installed tension part, reinstalled front, lowered the top and inserted lint trap. Job done. Quick and easy. The video was the key to the whole project.

Broken drum belt.

  • Customer: Bradley from Palm Bay FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
This was my first dryer repair. The only difficulty I had was figuring out how the belt tensioner was set up with the belt. The old belt broke so I didn't know how it was suppose to work. Anyway, it took a few minute to figure out that one end of the bracket was a "spring" that allowed it to flex a long ways! Pretty easy job.

broken dryer belt

  • Customer: Thomas from Waterford NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
instructions were clear and repair was easy

Does not turn or tumble

  • Customer: Charles Weston from Pikesville MD
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Well, to Figure the issue I took the entire thing apart. Actually a lot more than needed. I found the torn belt and ordered it. I did not realize I may need a new belt tensioner which is sold with a wheel for the belt to wrap around and be tensioned by. Actually the original just utilized a rubber c or u shaped design(no wheel) for the belt to slide over. Anyways, instead of ordering and waiting for a new wheeled belt tensioner, I installed new belt with all original parts and working fine. I did oil up the drum rollers to reduce noise. And since I took the whole thing apart I cleaned the lint from every place it could hide. Ps a coke can is said to be helpful to hold the drum up while installing the belt but I found a jug of laundry detergent did better. Totally easy project for someone with no appliance repair history

broken belt that makes the dryer drum go around

  • Customer: kevin from madison WI
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
The broken belt was found when I opened the dryer. The part number was on the belt and a quick online search led me to PartSelect. The part was available, delivered in less than 2 days and there was an online video showing the entire repair in detail.

Dryer drum stopped turning

  • Customer: Arthur from Felicity OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Popped the left and right side clips that hold the top, took out left and right side screws that held front face on, disconnected the wire that went to the door, tilted the door to me and lifted up from tabs on bottom. The old belt was broke, so it was easy to get off. Put the new belt on the drum making sure that the rubber ribs were touching the drum then I put the belt on the tensioner pully and motor pully. I rotated the drum by hand at least 1 full revolution to make sure that the belt was on right and it wasn't twisted, then I put everything back together. Easy 10 minute job... Art

Broken belt

  • Customer: James from Chicopee MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I watched the installation video. It was exactly as shown.

Clothes Dryer would not Tumble

  • Customer: John from Immokalee FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
The very first thing you want to do is Unplug the Dryer. I then took the two screws out that hold the lint screen to the top of the dryer. Then I used and old butter knife to pry the front top of the machine open. The top is held in place by two plastic clamps. Once I got the top loose I raise it up. Once I had it raised, I pulled up and out on the front panel where the dryer door is. I left the door switch connected and just put the panel off to the right. I then removed the old belt which was lying under the drum. The drum does drop slightly once you take the door off. This was one of the hardest part of the project for me as I did not have any help. This would be much easier if you just have one other person to hold the drum. Anyway, I then placed the new belt around the drum and used my left shoulder / arm to hold up the drum while feeding the belt in the slot on the tensioner and then over the dryer motor pulley. Make sure you don't twist the belt. I originally had a twist and when I hand turned the drum the belt came off the pulley and the tensioner. I had to rethread the belt through the slot on the pulley and then put the belt back on the dryer motor pulley. I then gave the drum a couple complete turns to make sure everything was staying in place. The tensioner on my dryer did not look like the instructions that came with the new belt. My belt tensioner is like a half circle and the belt just rides on it. I think if I had it to do over I would have purchased a new tensioner also. I feel that the belts constant motion against the tensioner probably causes it to wear out faster. Once I made sure evrything was staying on I replaced the front panel that has the door. You just slide the bottom into the slots while holding up on the drum so it lies on the felt padding around the door. Replace all screws and presto. Works like a new Dryer. Make sure you don't forget to plug it back in... Overall it's a pretty easy fix and much less expensive then a service call or purchasing a new Dryer.

Belt broke.

  • Customer: Laura from Saint Albans NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
After looking at your video, my brother and I put the belt back on, placed the front and back on and that was it. It required two of us but it went well and the machine is working fine. Thank you.
All Instructions for the 7MMGD6630TM0
826-840 of 899