7GU2300XTVS0 Whirlpool Dishwasher - Instructions

Received the new rinse aid cap and put it in. Fit perfectly!Thanks.

snapped on new wheel done

Pin for the top spinner broke off. Watched the video on the website and went to fix dishwasher. Found out that I only needed to remove baskets, cover bottom with a towel so screws didn't fall into unreachable areas, then removed one screw on the top. Removed broken pin and installed new spinner and pin. Less than five minutes from a woman who's never done this before. Felt like a pro!! Your easy to use website to find parts and repair video made it possible. Thanks a million!!!

Pulled dishwasher out, laid it down on its back. that made eaiser to get to the motor. Pulled the motor off then put the new motor on.

fOLLOW THE VIDEO AND THE REPAIR GOES VERY WELL. You have a fantastic web site to diagnose the problem and fix it.

Solution was very simple with the side mounting bracket kit, the only problem was somehow one of the brackets was damaged out of the box . There's a slight off-set on the bracket to allow it to fit properly next to the dishwasher but this one had been flatten out. Had to have happened before going into the shipping box because they were very well protected with bubblewrap. Also, brackets are fairly heavy gage metal so it would have taken some amount of force to do this. Fortunately I was was able to bend it back into a useable shape. It wasn't perfect to look at but because it's mounted behind the side of the dishwasher it didn't matter as long as it worked.

The first check was for any circuit breakers that tripped. Upon finding the circuit breakers intact, I removed the front panel from the dishwasher and verified power was up to the panel, which is was. I removed the kick panel and located documentation for schematics and troubleshooting. This led me to the bi-metal switch (non-resettable). After turning off the power, I checked the continuity across the switch and found it was open. Then I provided a short across the switch and turned the power on to verify panel was working properly, which is was. This verified the bi-metal (thermal switch) was the issue. I then ordered the switch and installed it per the instructions. While looking for the switch, I did run across another post suggesting the additional wire leads with the kit should be included since they act as a heat sink. With the new switch installed along with the additional wire leads, the dishwasher is working fine.

Removed plastic end caps from dish rack rail and slid rack off front of rail. Removed rear broken wheel and mount assemble that rail runs on. I believe this took a 3/16" socket which most people would not have and would prevent them from removing this part. With the right tool it was easy, without the tool it would be impossible. Buying tool at local hardware store would be much cheaper than calling repair man. After rear wheel mount assembly was removed, I slid rail forward so I could easily remove the rear rail end cap. I then mounted new wheel mount assemble using original screws and then slid rail through both wheel assemblies and snapped rail rear end cap back into rail. I then slid the upper dish rack on to the rails on both side, slid the wrack back and then snapped the end caps back into the rails fronts on bothe sides. The job was done and the dishwasher was ready for service.

Removed the screws under the counter, retracted the leveling bolt jacks, turned off power to unit, turned off water supply to unit and made sure that all the water was out of the unit. Disconnect supply and drain lines. slide out unit from under counter and put protection over the door then lay it over onto the door. unplug the motor remove the screw that holds the motor in place, turn the motor counterclock wise, wiggle the motor in a side to side motion and it will come right out.(GLOVES ARE RECOMENDED FOR THIS OPERATION). Use cooking spray or olive oil on the O-ring. line up the arrow on the pump housing with the arrow on the pump motor and put the unit back together in the reverse order. Test the unit with a operation of a quick rinse to check of leaks. This is a very easy repair.

Removed unit from counter. Replaced element.

I remodeled my kitchen with new cabinets. In order to better utilize cabinet space, I located the dishwasher away from the sink, which means that I had to have a longer drain hose. The store I purchased the dishwasher from didn't have a longer hose, so I went online and found it on this website. Thanks for the quick shipment. I ordered it using standard delivery and received it in less than three days. I have book marked this website for future use.

Repair was simple. Pulled out the old gasket and pushed in the new one.

Ordered Rinse Aid Cap and received the next day. Placed in the dishwasher Rinse Aid Cap position and locked in. A perfect fit.

Unhook electrical/water supply, removed dishwasher, flip upside down, Remove wire connector from motor, remove bolt from motor, turn motor and remove, install new motor in reverse process.

Pulled Dishwasher out, turned off power. Did not have to disconnect any hoses or electrical, because when I did the original installation, I left plenty of slack, so as to be able to pull it out. Next, tipped it on it's side, unplugged the harness, undid the bolt, turned motor 1/4 turn, pulled it out. To, re-install, just reversed the process. About 1 hour.Followed Excellent instructions on video. Was very impressed with delivery time. Only about 30 hours, from the time I ordered, to receiving part. Reg. ground.