Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Ice dispenser freezing up, dispenser door not closing completely.
First off, if you have the stainless steel panel inserts on your refrigerator you'll need to remove those to do this repair. I kept looking for the access holes on the underside of the dispenser panel that you're supposed to insert a screwdriver into to pry it off. It wasn't until I removed the freezer door handle, slid the lower stainless panel insert out, and removed the rail just beneath the dispenser that I could see and access these holes. I also removed the upper stainless panel and rail just above the dispenser to allow enough movement get the dispenser cover off and out. The rest of the repair is pretty straightforward. The old ice door was beaten up and not closing completely, this was letting warm air into the freezer which was melting and re-freezing. This kit fixed the problem.
Water filter end broke off so I could not get out of housing.
Removed 2 screws holding housing to frame. Pulled housing out 10 inches. Removed water lines. Attached water lines to new housing. Pushed back into place. Secured to frame with 2 screws. Put in new filter. DONE!
Removed the ice bin and turned it over. Removed the old coupling and replaced with the new one, reusing the screw that holds it in place. Then removed the cover plate over the drive shaft that comes out of the door. Pulled out the old shaft and removed the plastic ring that keeps stuff from falling into the motor area. Put the ring onto the new shaft and slowly put the new shaft down into the door until it seated in the motor assembly. Replaced the cover plate with the nut driver and voila! The Ice Age has returned. An easy fix once I determined that the drive shaft end was worn where it engages the coupling, causing it to slip and not move the ice dispenser arm.
I just removed a few screews and took the cover out of the ice box. Put my voltage meter to the refrigeator and realized the the unit was not defrosting...I then got the part number and entered it in on your web site. A few days later my part arrived. I put the part on and in just about 20 minutes I was up an running again...Thank you Part Select for fast and great service. I own 35 rental properties and having a online appliance parts store really saves me a lot of time and money.
Disconnect power to refrigerator. Removed all food from Freezer. Removed all Shelves and shelf clips. Used phillips screwdriver and removed 6 screws from lower rear panel covering evaporator coil. Removed panel. Pulled plastic fan blade off top of motor shaft. Unclip top front of black motor retainer clip which then allowed the rear clip to unhook. Removed clip. Then removed 3 wires from fan motor, noting proper location for replacement. Slide the fan motor out to the left. Installed new motor. Reinstalled clip, hooking rear side first. Then rehooked the 3 wires. Slide fan blade back on top until secure. Tested everything at this point before reassembling rear panel. Then replace rear panel, replace the 6 screws, replace shelf clips and shelves and replace food. Very easy to do and saved about $150 over a service call to troubleshoot and re-visit to install after getting part
Remove the kick panel and simply turn the filter counter clockwise and it slips right out.Water shuts off when filter is removed.After new filter is installed be sure to bleed line thru the water outlet in door to clear air in system.When first water is bled the water will continue to run until line drains. Then comes the air.Bleed until water is clear.Its an easy job and can save you$$$$$.Ray Palm Bch Fl.
The hardest part was getting the front cover plate off. I used two kitchen knifes one in each slot on the bottom of the plate and pried it off and unplug it. I removed one screw to release arm. I then used long nose pliers to remove the pin on door arm assemble. Then unplug door heater. New door has no heater. The heater had cooked the plastic arm, which caused the arm to fail. Then reassemble in reverse order.
removed the clip that the motor was attached too put the new motor back on reinstalled the clip back on the fridge plugged the wire harness in and works perfect now . it was easier to remove the clip than to try to install the motor by itself its just to tight and you cant get in there
It was really easy to do. The water filter is in the front of the refrigerator. Less than 30 seconds. I am very happy with PartSelect. I bought parts for my dryer too. New lint filter, timer knob and door handle. Parts arrive immediately. I am sure I will be back to PartSelect.com.
Emiter blinking red; ice maker stopped working. Called appliance repair, said electronic control boards needed to be replaced. Quoted me $275, including parts. Ordered part at partselect.com, installed in 15 min and ice maker started producing ice. Also discovered on other online forums that this part is a common failure on these model refrigerators. Very easy to swap out, plug & play. Make sure to unplug appliance before performing repair due to shock risk.
Taped plastic cover to get it out of the way with duct tape - removed three screws on each side - removed retaining screw for each module - carefully disengaged module using small flat head screw driver being sure to release the plastic retainer and then reverse the process. Be sure new modules snap into place.
Biggest problem was initially figuring out what the problem was. Turning off the ice maker had no effect and it just kept making ice.
Well I changed out the optical boards which I thought were the problem and the ice maker is still not making any ice. I can see the ice makers fingers rotating but there is no water entering through the tube. I jumped the water manifold in the back and water comes out but I cant figure out what is not telling it to run water and fill the ice tray. Any ideas would be appreciated I guess i'll replace the ice maker next. Thanks in advance.
