Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The old igniter no longer worked properly, so I needed to install a new one.
1. Unplug the range to ensure there is no electricity running through the range. The repair can be done with the propane/gas line still connected.
2. If possible, remove the storage drawer for ease of access.
3. Remove the screw from the metal plate in the left corner of the oven. Detach the end of the igniter cord that you find plugged in there.
4. Remove the two screws that hold the igniter in place. The old igniter should fall to the bottom of the range.
5. Take a picture of the two other cord connections that run into the middle of the back wall. This will come in handy for reference when you install the new igniter.
6. Route the longer extension of the new igniter cord through the hole in the metal corner plate, attach the cord, and put the screw back in to secure the corner plate.
7. Affix the new igniter to the same spot the old one had been in, using the two screws from step 4.
8. Plug in the two shorter cord extensions, using the photo from step 5 if necessary.
9. Reattach the drawer if necessary and plug the range back in.
10. Set the clock, then set the oven to a desired temperature to begin heating. If the repair was successful, the igniter will light the gas piped into the range, and you will see a ring of flame.
Stovetop worked fine, but Oven didn't always light.
Open oven door and remove metal splash plate on bottom of oven by removing two screws in back. Remove heat distribution plate (metal) by unscrewing a single nut with pliers. Now the ignitor is visible. Unscrew old ignitor by backing off two screws. Detach the wires and reattach to new ignitor. (a cover plate may have to unbolt from the left back corner to get at one of the wiring connections.) Reattach new ignitor and then flame distribution plate. Put on splash cover and tighten back screws. Test oven, it should light within 1 minute. All is done.
I forgot to remove something I had saved in the oven, planning to remove it before using the range.
Very simple. Removed oven rack that had melted residue on it and replaced it with the new one from your company. I want to tell you that the delivery service I received was just geat. Took less than 48 hours to arrive at my home from the time I placed the order on line. Keep up the good work and I will be happy to share my experience with those in need of you services. Thanks. Marilyn Kasson
1)First unplug range. On inside of oven, there's a copper, pen-like object connected to a copper wire. 2)Open the clips on side of oven that hold the pen-like object(the probe.) 3)Open the lid of the stove. On left hand side, there's a hole through which to pull the copper wire and probe out of the stove. Or you can just as easily use wire cutters to cut off probe and just pull wire from the oven through the hole. 4)Pull off the oven's thermostat control knob. Using screwdriver, unscrew both screws under where the knob was. 5)Now pull the flat wire connecters from both sides of the old thermostat. Remember which wire goes on which side. 6)Remove old thermostat and copper wire that's connected to it. Replace thermostat. 7)Feed copper wire with probe through hole on left side of stove. 8)Slide flat wire connecters onto sides of new thermostat. Replace screws. Insert new probe into clips on side of oven. Close stove cover. Replace thermostat control knob. Plug in range. Test thermostat. 9)According to owner's manual, turn oven to 350° and oven should be no more than 50° above setting.
Partselect always have their install video with the parts they sell so it was easy. I know contractors must not be happy with people like partselect and YouTube with all the instructional videos they supply us with. Keep up the great work partselect.
Stove was dropped and had broken, bent frame and adjuster feet
New ones fit perfectly. Take a minute to bend the frame straight. Then and I used oversize screws on the replacement parts as the drop had stripped out the screw holes of the frame.
Disassembled inside of oven. Slid away from wall opened back replaced safety valve and igniter. Safety valve was good changed only because it was apart. Resemble and test sat. Kept old safety valve for emergency spare.
Your website is great...easy and it literally took me no mote than 5 minutes to find what I needed and order...and received it VERY quickly. Must say I was dreading going to some parts house that we have in our town in bad area, and searching on dusty shelves for what I needed...am so glad I found you!!
Pulled out broiler drawer, removed 3 bolts, plugged in new igniter. Only issue was one of the tiny bolts stripped, so now only have 2 holding it in place.