Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The switch became intermittent - Possibly a poor designe
Used a small screw driver inserted into the front of the switch (facing the front) and pried until the switch was coming out. When out, I removed the connect harness and replace the switch with a new one.
Read previous tips Taped off area around switch to protect surface Used putty knife to extract switch Used screwdriver to separate connector from switch Plugged in connector Pushed switch assembly into opening Removed tape
The spring broke on the flapper (mullion) on my refrigerator. I sent a chat message to PartsSelect (they answered right away) to see if they had a replacement spring but it was not available so had to order the whole mullion. They gave me the part # I would have to order. It arrived quickly. The new mullion didn’t have a visible spring but it worked the same if not better. I just had to remove 2 screws on the center plate on the existing mullion, pull the plate out enough so you will be able to slide the mullion (the wires are under the plate kind of like the ones you see on a ceiling smoke detector) but you can’t get under the plate until you release the mullion. Push up on the mullion so that the plastic tabs on the top and bottom are released. Once the mullion is released (you have to hold it), you’ll see the wires. Unhook the wire part by just pushing down on the little tab and remove it. To install the new one, just reverse the steps. Align the top and bottom plastic tabs to fit into the slots, just enough to hold it in place. If the plastic tabs are not already flipped out, you’ll have to just flip them out. The top tab does not have tension but the bottom tab has tension so just push on it with your finger to flip it out. The plate covering the electrical is a rather tight fit and you have to make sure the little tab on the inside of the plate is above and behind the tab on the inside where the wires are so it slides behind it so you can get it in position before sliding the mullion back down into place and the electrical plate is in place too. Then screw the 2 screws back in. The hardest part is holding the mullion while un-attaching the electrical and just make sure you stuff the wires in enough so you can get the plate back in position. I’m a 75 yr old woman and managed fine by myself. At first when installing the new one, I couldn’t slide the mullion down enough to get the electrical plate in position and then realized I had to have the little tab inside the electrical plate behind the tab inside the wire compartment so they didn’t hit one another when pushing the mullion back down. Then, all went fine.
Remove and replace cracked crisper drawer cover frame
1) Remove three drawers and items sitting on glass shelf. 2) Remove glass shelf 3) Remove entire crisper plastic unit from refrig. 4) Unscrew 6 screws holding uprights with a philips head screwdriver. 5) Remove top frame and replace with new frame. 6) Replace 6 screws and tighten them. 7) Replace entire frame in refrig and replace 3 drawers and glass shelf. 8) Done
Unplugged the frig and removed two phillip screws on flapper door of left door... Unplugged the electrical connector and removed flapper... Picked up new flapper and snapped electrical contractor together... Slid new flapper bar into place and inserted two phillip screws... Job complete in 15 minutes...
I have moderate to good mechanical skills, but getting the old switch out was a sizeable challenge. Since this switch suffered some damage during extraction, I was lucky to have ordered a new one to replace it. Reinstall took approximately 90 seconds. PartSelect saved me an expensive service call.
The hose that feeds the Ice Maker broke,right where it goes in the Fridge.
I actually didn't use what I got. Because there was all kinds of tubing coiled up in the door. We just fed the exsess all the way through the Fridge,and Bingo! It was done.
The old ice maker had cracked and broken, and would no longer make ice.
Six screws to remove the old one (I looked up the process on Youtube) and six screws had it back in tip top shape. Three wire connections, two were plug in and one was a ground wire. BTW: It was a 3 wire, not a 6 wire. I had ordered that by mistake and PartSelect made the return and replacement very easy.
