Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Broken Oven Door
This is an easy fix. Just before the holidays, it was imperative that this appliance be in top shape. Since the door 'hung' wrong, it was determined that the hinge pin broke. Remove the 2 phillips head screws on the door and open the door to the to a 15 degree opening. This position allows you to slip the door off the hinge levers. Now that the door is off, replace the hinge pin and slip the retainer ring on with a screw driver blade to push it on the pin. Slide the door back on the levers and fasten the retainer screws. DONE!
First I removed the ovem door, then I removed the 4 screws, unplugged element and plugged in the new one, then replace the screws and door. It should have been a 10 min job but I'm old and a bit fat...slowed me down.
First tried to replace the glass and gasket without removing the oven door. Removed all screws and took the door apart. However, I found it was very hard to get the gasket to stay in place and put the glass window in place with the door frame still attached to the oven and upright. Decided to go ahead and lift the door off the hinges by removing the two final screws. Then the door could be layed flat on the floor and it was much easier to put in the insulation and glass pane.
The honeycomb filter in the vent was missing so I bought the entire vent cap.. Thought it attach with 2 screws from inside the oven.. BUT -- when you loosen the screws, it wouldn't drop.. Looked at the new part and saw that it attaches to the vent outside the oven as well.. So to replace this puppy, you have to pull the cabinet apart..
Left it for another day.. Hopefully no grease fires..
1. Move oven out from wall 2. Remove back panel of oven, 8 screws 3. Remove 3 screws inside oven holding element 4. Pulled wire connections off of element 5. Reverse procedure to install new element
Just pulled the old support out with pliers and installed the new one which snaps in. Not sure why the support melted as it has been the same one twice now. Keep extra support clips on hand, but no need as Parts Select had the new ones here next day.
The microwave is the upper unit of combination microwave & conventional oven. Disconnect power to the unit. Slide unit out of built-in cabinet to expose the top shield of the microwave. Remove 5 screws holding top cover in place. Remove cover, which exposes the belt reel and drive motor. Install the new belt by threading it on the drive motor pulley, then walk the new belt on the stirrer pulley. Replace the top cover and reinstall the 5 screws. Reinstall the combination unit in the wall cabinet. Reconnect electrical power. Task Complete. The belt just seem to die of old age about every seven year. Without the wave disperser operating, the microwave oven does not give even heating.
Ordered element and received it the next day. Removed two screws that holds element in place. I then pulled the element out about 3 or 4 inches and disconnected the two wires. Put new element in connected the wires mounted element in place with the two screws. Now works great!
Unplug first then took back off and took wire clips off and connectected the other on in worked fine you will like part select I just ordered apart for my frig. Waiting for it now.
The upper broiler element had burnt and broken into.
I must compliment PartSelect on their quick responce and delivery of the item ordered. It arrived a day after I had ordered it. Trust me, the $40.00 I spent on the item was way cheaper than having a repair service fix it or having the entire oven replaced. I would highly recomend anyone to utilize PartSelect.
Original bake element had open circuited, fortunately the day after Thanksgiving and not on Thanksgiving
Removed the two Philips head screws that attach the element to the back wall of the oven. Pulled off the two wire terminals from the spades on the back of the element. Pushed the two wire terminals onto the spades on the back of the new element. Noticed that one was not tight, so disconnected, squeezed down the wire terminal, and reconnected. Inserted the two screws that attach the element to the back wall of the oven. Element works fine.
First, shut off the power at the breaker panel. Next, I simply unscrewed the screws holding in each element, disconnected the leads, reconnected the leads to the new elements, positioned each element & reinserted the screws. A suggestion: Before loosening the screws, a light shot of PB Blaster or similar might help.
Removed all terminals and block mounting screws. Repaired one burnt terminal and reassembled. Replacement part was an exact fit and reassembly whnet very well.
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, Removed the old element and installed the new one