Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dishwasher would not circulate water to clean
My husband pulled out the dishwasher and removed the faulty part and installed the new one. We found info on the parts source website to assist us. Dishwasher works great!!! Someone from the company we purchased it from had replaced it several years ago, and the seal at the bottom had leaked and the motor had siezed because of the water. We also discoved that the water line was severly kinked in 2 places, so we installed a flexable hose. Now my dishwasher is quiet, fills much faster and all this for a fraction of the price of a new appliance. Would recommend this website.
Pulled out dishwasher. Took out old screws. Unsnapped end of rack slid new wheel in and attached to side. Very Very easy. It was great to get the part so fast and take care of this repair ourselves.
Pump/motor assembly make making loud noise & door balance cable broken
I removed the dishwasher from under the cabinet. This is what took the most time. Before removing the dishwasher from under the cabinet I disconnected the drain cable to remove all the water from unit. After removing the dishwasher I tipped the unit on its left side. The motor/pump assembly is held in with one screw. After removing this screw the pump/motor assembly comes out with a 1/8 turn counter clock wise. The replacement pump/motor assembly was put back in in reverse order. After the pump/motor assembly was replaced I replaced the door balance cable kit on the right side of the unit. Next I tipped the unit on to its right side and replace the left balance cable kit. After this all that was left was to return the unit back under the cabinet and hook up the water supply line, the drain line, and the power.
First I removed the screws holding the outside door panel to the inside door panel. Next (at this was the tricky part) was separating the panels. In our model of dishwasher, there is a layer of Styrofoam between the two panel to reduce noise. Unfortunately the Styrofoam is glued to both panels. Separating it without damage was not possible. So it was done with brute force and the Styrofoam broke in several places.
Replacing the dispenser involved removing six screws, disconnecting the wires and popping the dispenser out. The new one went in easily although there seemed to be a correct amount of tightening to do. It was tricky to get the cover back on because the Styrofoam pieces had to go back together like a puzzle.
Once reassembled, I ran the machine and it leaked at the dispenser. So the cover came back off. This time I played with the adjustment of the dispenser, testing it with the outside cover off, to insure that I had a tight, non-leaking seal. Once done, I put the cover back on and we are back in business.
The new dispensers do not have connections for the "Add Rinse Aid" light. They use a visual indicator on the dispenser itself. I simply taped the wire for the indicator light up and left it inside the door.
One last note, on our unit, the outside door panel is two pieces. I needed only to removed the lower portion for this repair. Unfortunately, I removed both and in the process broke the small plastic end on the door latch requiring me to purchase a new one. Bummer. That was a 10 minute repair though.
Poor seal on old gasket caused water to leak during dishwasher operation.
I simply pulled out the old gasket and pushed the new one in with my fingers. I had to trim about an inch off the length with a utility knife. The seal is nice and tight now and we have no more water leakage.
My 2 parts were delivered very quickly. We had been putting off the repair, mainly because any time you hire a capable repair man, the charge to "walk through the door"is very high. I actually thought about buying a new DW for this reason . . . Then I googleD PARTS, And was lucky to find PARTS SELECT. I was most impressed with the graph layout of the parts, which enables the buyer to actually measure the part being replaced to be sure the correct item is being ordered. The instructions were excellent, and this grandmother took care of the repair, easily.
Dishwasher door falls down as soon as it is unlatched and moved just a few inches open
This kit comes with the link cords and the balance wheels. I only needed the cords. I undid the set screws under the counter edge and slid the Dishwasher out from under the counter. One of the links had a broken cord and the spring had snapped to the very back of the space and was a bit hard to find. I used the good side as a guide to see how to thread the cord correctly. I did not replace the wheels since they appeared to be in good shape and looked like they might be a bit more difficult to replace than just the cord. For a second I thought I had ordered the wrong part because the new cord's attachment point at the hinge did not look exactly like the originals but the new design worked just like the original. I did need one other person to help stretch the spring and hold the door in the best position so I could attach the cord to the hinge. It's working perfectly now and I saved the wheels in case I need them later.
Replaced pump and motor. For the price of the products individually, it only made sense to do the whole thing. As someone else mentioned, much easier to remove the dishwasher and turn it on it's side to remove/replace. Disconnect 3 fittings, 3 stop devices and remove. Other than getting about 20 cuts on my hands from all the metal, it wasn't bad at all.
Removed leads from fuse and installed jumper wire (while the power was off, then turned back on) to determine that circuit board was still good. Ordered new fuse and installed using existing wire connections. Did not splice in new connectors that came with fuse. Wires were clean and good and did not want to cut and splice.
Dishwasher's "clean" light just blinked - wouldn't run. Repairman came and found out problem and suggested I could fix it myself
Since I had watched a repairman diagnose the problem, it was eash to reproduce how to pull the unit out from the wall and find the faulty part to remove it and replace it with the new thermistor. Two wires to disconnect and connect and repair nearly complete. Pushed it back in, screwed it back to the cabinet and installed foot plate and done.
I had removed this part several times before, it had clogged from sediment, so I had practice. That issue was resolved, but I determined the water level during the wash and rinse cycles was low, and the valve appeared to be the culprit. The trick is to remove the valve from the bracket, removing the single screw, and sliding the unit so the tangs on the bracket can be pushed to the rear and then towards the front. When you disconnect the electrical connection, then the valve can be pulled out towards the front for better access and to disconnect, if your supply hose is long enough. That makes swinging the wrench easier. Other wise it is tedious. Make sure to reapply thread tape after reconnecting the supply hose.
Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
17 of 29 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Clip no longer held spinner in place
Bent the plastic housing down holding the spinner. Slipped the top of clip in slot on top of housing. Attached spinner and bottom of clip by holding top clip and pushing bottom of clip in place. No tools were needed.
Removed first part of the broken part from the top rack of the dishwasher from below.
Removed the screw from the bottom of the sprayer arm to release the second half of the broken part.
Threaded new part in sprayer arm and replaced screw.
Attached part to top rack of dishwasher from below. This part was difficult. (The part appeared to be a little larger than the original.) It was a two person job, one person pushing down on the rack and the second pushing upwardand inward on the part it click to click it into place. Dishwasher now works great.