Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
broken fill valve
that there is 90% of the repair made easy when you have the correct part. there is no better then direct replacement parts. the repair was self explanitory. one screw, two lines, lock in place, done. thanks for having the correct parts,that is what makes a job simple.
Removed old seal, cleaned track, applied adhesive for new seal, seated new seal in track, closed door for 24 hours to allow adhesive to cure, then used dishwasher without difficulty. An easy repair.
Pulled out dishwasher. Took out old screws. Unsnapped end of rack slid new wheel in and attached to side. Very Very easy. It was great to get the part so fast and take care of this repair ourselves.
Take 10 lower star srews from inside of door (5 per/side) that hold on front. Remove front door panel. Remove 6 screws in detergent dispenser and replace.
I did not lock the cap good enough and it fell off and melted
I just placed the cap back on, it worked great, fit fine and so glad I found this part. I was thinking of ways to McGyver it, thinking it would be impossible to find a new part. Glad i fount this site and the part.
Pump/motor assembly make making loud noise & door balance cable broken
I removed the dishwasher from under the cabinet. This is what took the most time. Before removing the dishwasher from under the cabinet I disconnected the drain cable to remove all the water from unit. After removing the dishwasher I tipped the unit on its left side. The motor/pump assembly is held in with one screw. After removing this screw the pump/motor assembly comes out with a 1/8 turn counter clock wise. The replacement pump/motor assembly was put back in in reverse order. After the pump/motor assembly was replaced I replaced the door balance cable kit on the right side of the unit. Next I tipped the unit on to its right side and replace the left balance cable kit. After this all that was left was to return the unit back under the cabinet and hook up the water supply line, the drain line, and the power.
After reading other posts I opened the dishwasher door put a support underneath it. Knowing that all the screws were not the same I carefully unscrewed them and placed them on a towel in order of extraction. After all the screws were taken out, I lifted the door up gently and lifted it out of its place and put it aside. Now I could see the hex screws holding in the soap dispenser. I then unscrewed the screws and place the frame aside. Next I gently pulled the electrical connector to the dispensing unit off. After locating a snap tab on top on the left hand side and one underneath on the right hand side, I gently lifted the tab and the dispenser unit moved slightly forward. After gently prying the lower tab on the right hand side the dispensing unit was loose. I just reversed the process to put things back together. I was not necessary to have any help taking things apart but it was very helpful having a second set of hands when we put it back together. Lining up the screws for the door was much easier with two people. After installation, I started the dishwasher to check for leaks. Everything was fine. Very satisfied to be able to repair/replace this unit without calling a tech. If you can change a spark plug on a lawnmower you can replace a soap dispenser on a dishwasher such as mine. Very quick delivery from parts source. Thank you.
Dishwasher door falls down as soon as it is unlatched and moved just a few inches open
This kit comes with the link cords and the balance wheels. I only needed the cords. I undid the set screws under the counter edge and slid the Dishwasher out from under the counter. One of the links had a broken cord and the spring had snapped to the very back of the space and was a bit hard to find. I used the good side as a guide to see how to thread the cord correctly. I did not replace the wheels since they appeared to be in good shape and looked like they might be a bit more difficult to replace than just the cord. For a second I thought I had ordered the wrong part because the new cord's attachment point at the hinge did not look exactly like the originals but the new design worked just like the original. I did need one other person to help stretch the spring and hold the door in the best position so I could attach the cord to the hinge. It's working perfectly now and I saved the wheels in case I need them later.
I changed the Springs,Cables,Hinges (both) also changed both latches one on the door and the striker on the top of the tub. Problem still exists. Call worldpool today they never heard of this issue but if you google kitchenaid Dishwasher door pops open you get all kinds of hits.. You guys were great no problem with the parts..
Soap dispenser unit could have been repaired by pushing the plastic arm back home and adding two drops of instant glue to keep the plastic shaft in proper place. Didn't need to purchage a new unit.
Nutdriver, Socket set, Wrench (Adjustable), Wrench set
13 of 15 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Unit started only intermittently and then finally fail to start at all.
Unplugged unit from power source.Removed the screws fastening the interior panel to the door. Removed latch assembly from the door after disconnecting two wires to the microswitch. Removed microswitch from the latch assembly, then installed same microswitch in new latch assembly. Re-connected wires and re-installed latch assembly. Re-installed interior panel with screws. Re-connected unit to power source. Tested unit. Has started reliably ever since.
The upper spinner was laying in the top washer basket. I went online but no help was avaiable. Went to store where we purchased dishwasher and they gave me part number to order but not online I had to call to order. Part arrived in about three days. I took two screws loose on the top of dishwasher removed broke retainer to put new retainer in but I drop it into dishwasher so you have to me very careful so I tried to order just the retainer but is not sold by it self. Had to order whole new kit. Other than that it is easy dishwasher runs like a new one.
First, ordering parts and getting diagrams from parts select is so efficient and make tthe installation so manageable. Using installation tips off the site gives u confidence to do it. My issue was that I could not get the dishwasher from under the counter. I removed the kick plate and screws holding it to the counter, but it was not coming out all the way. So I had to use a coat hanger to hook the spring. I attached the nylon cord first. Then I pulled the spring taut with the hanger and it was easy to thread the cord around the pulley system. I actually attached it to the door before tensioning the spring to make it easier. Door works great now.
The first thing I did to repair my diswasher was call a repair company. They wanted $175.00 just to look at it, so I scheduled an appointment. Then, I did an internet search for dishwasher repair. I learned about bi-metal fuses, and how to check them. I found my bi-metal fuse was bad, so I ordered a new one through parts select. My part arrived in two days. I installed it easily, and the dishwasher worked. Finally, I canceled the repair appointment.