Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Loud squeal when spin cycle finished, white powder under washer
Read DIY review from William, Middleton, OH on 01-15-08. Tip on how to relieve spring pressure on brake assembly worked like a dream (3ea 10-24X2 bolts/machine screws). Replaced brake and machine works like new and was an inexpensive fix. Once the shell/housing is off the machine, tub can be turned upside down and the base doesn't need to be removed. White powder under machine was a plastic wear ring that tells you when your brake rotor needs to be changed. Brake rotor still had lining but was much thinner than replacement part. Note* Use putty knife to push in clips on front to release the top lid section.
Open the top of the washing machine by using a putty knife to release the latches at the right and left side. Prop up the top so it doesn't fall while working. Remove the inlet hoses and put in bucket to catch water. Remove the two screws that hold the inlet valve in place. Remove the wires from the inlet valve. (One of the spade connectors one wire broke and I had to replace it.) I used needle nose pliers to pull the spade connectors off. Remove the outlet hose. Throw out old valve assembly. Attach hose to new valve assembly. (My old valve assy outlet was slightly smaller in diameter than the new valve, but I was able to get the outlet hose to stretch enough to fit--couldn't use old spring clamp though, but new valve came with a hose clamp--worked fine.) Attach wires same way as they cam off old valve. Position and use the two screws to screw assy back into back of washing machine. (The screws had to tap the holes on the valve, so start out a little hard.) Reattach the inlet hoses and check for leaks. I also ran both the hot and cold in a cycle and the reraised the top to check for any leaks internal to the machine. Pus the top back down to engage its fastening clips. Job done. My washing machine is 23 years old.
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
I removed the part that was still attached to the washer and installed the new flume. It took less than five minutes and a repair that would have cost over $85 cost less than $10 and I am no plumber!
I didn’t have special tool for brake but punch and hammer worked. Seal was easy to replace. Several videos online to show you how. It wasn’t worth it to tear apart the transmission and buy more parts/seals (if they were even available). But I didn’t know how much oil was in it. I drilled a hole in the side to somewhat check level and added 80-90 gear oil. It was almost empty and added almost a quart. Used a self taping screw/bolt with gasket sealer to plug the hole. I got 34 yrs out of this washer. If it fails, oh well. Just hate to buy a new one that only last 10yrs if im lucky.
Removed the screw from the side of the lid of the washer. Took off the old Lid Switch Actuator and screwed in the new one. Took a little elbow grease because the old screw was tight but no longer than 15 minutes tops.
i took off the old belt and i took off the motor pulley with the pliers and srewdriver. i put the new pulley in with my hand and gave it a hit with the palm until it snap in and then i put the belt on by rotating the main pulley on tub till the belt was pulley on.
I opened up the top of the washer which exposed the tub, I took the top ring off the tub and under in side of the ring is the seal. Took the old one out and put the new one in. The old seal was completely wore out. It was real easy. Finding the part is usually the hardest part, but thanks to Parts Select finding the part was the easiest part of the repair.
Noticed nick in drive belt durng inspection and cleaning
Washer was making noise especially when spinning. I took the washer apart to clean it, That is what it really needed. Also adjusted the water level to prevent overflows which caused soap and water to get underneath into the drive belt area as well. During inspection noticed a nick in the drive belt, Although this was not really causing immediate problem wanted to repalce it to prevent problems. Ordered the belt; it came in two days with no special postage. To install, just leaned the washer over on its front on a slight incline. Took old belt off and put new on by turning the big pulley. It is spring tensioned, so no tools. This may be the easiest part repacement I ever did. Took longer to write this paragraph than to repalce the belt.
No hot water was making it into the laundry cycle.
First I unplugged the machine, then turned the water supply off in order to disconnect the hoses at the back of the machine. Next I pulled the top up and leaned it back so I could access the water valve at the rear of the machine (You might have to use a screw driver to pry the top off the pins which hold it down in front...). I then unscrewed the the valve and disconnected the wiring and, in order, re-connected to the new valve. Now reverse and turn on the water and yes, the new valve fixed the hot water problem. We can now do the "whites".
lid switch acuator broke and some cycles would not work
unscrew the screw holding the broken part in the lid to remove the old part and tighten the screw to a firm position to hold the new piece in place. Now working fine.
Once the washer was unplugged, i removed the two screws on the back pannel, disconnected the three wires, rubber water line, and two screws holding it to the control panel. Quite simply reversed the process with the replacement part i ordered, which arrived overnight, and the problem was solved.
I removed four screws to remove a plate to get access to the pump. Then I removed 3 screws to remove the pump. I then put the new pump in place and put the 3 screws back in the pump. Then I put the plate back on and put the 4 screws back in. Then I put the belt on and put the washing machine back in place and connected the water lines and drain line and plugged the washing machine back in and then tested the washing machine to make sure it worked. Job completed.
Disconnect electricity....remove front panel by gently prying up lid.... Remove two small screws at corners of front panel. You may need small nutdriver here or very small hands, you can easily swivel tub out of the way....once front panel is off water pump is at the bottom right... It is only connected by two squeeze clamps and 3 nuts... This is obviously where the adjustable wrench and nutdriver come in very handy... Otherwise this job will be a bit longer....be prepared for residual water to pour out...you will need towels or a bucket....replace old with new one by reversing the process...at this point tilt the entire washer on it's backside or at least at a 45 degree angle to access the bottom... Swivel the motor away to slack up the belt...remove belt and replace in reverse order of diassembling.... Should take no more than 15 minutes.... Good luck!!!!!