59675522400 Kenmore Refrigerator - Instructions

took off the ice maker, unscrewed the body, replace icemaker shut-off arm, water fill cup & bearing, reconnected the unit & have ice now, Thank you PartSelect

Simply remove the filter and insert the bypass cap in its place. Cap turned a little hard but if your careful everything goes together easily.

The large pull out full width drawer cover hinge pin broke off on the left side. The repair is easy with just two tools, a 1/4" nut driver and a phillips head screw driver. I removed the two conventional drawers that sit above the wide drawer with the broken hinge. Next lift out the glass divider that sits on top of the wide drawer and set it aside and remove the two braces front and back by lifting them out of their respective grooves. Remove the wide drawer with the lid by pushing in on the two black clips on each side of the drawer slide up towards the front and pull entire drawer out while putting pressure on the two clips at the same time. The drawer should come out leaving the drawer slides behind. Unscrew the 1/4" hex screws on the broken side panel using the nut driver and gently pull the side panel straight back toward you. Remove the drawer slide from the broken piece by unscrewing the two phillips head screws and rescrew the drawer slide onto the new side panel. Replace everything in reverse order. One note: do not use too much torque on the screws when replacing the parts as they only screw into plastic, this will avoid them stripping out. A snug fit is all you're after. There now, go pop a beer and sit down and relax, you are now a refrigerator repair man!

easy enough, removed 3 screws, unplugged wiring harness, put new unit on work bench, put old wire harness on new unit, put old motor cover on new unit,(the only trouble i had was figuring out how to swap the light blue plastic piece for the white plastic piece, i just put a screwdriver underneath and applied pressure) plugged harness back into freezer, turned water back on and waited... 2 hours later heard beautiful ice cubes dropping into tray :)

So simple I couldn't believe it! Twist out the old filter then twist in the new! Easy Peasy!

Remove two upper trays. glass shelf and shelf brackets. Remove bottom tray. unscrew side with back vent openings and remove with humidifier controls attached. Carefully remove control arms and back vent cover. Install on new unit and screw back in place. Check to make sure hinge pin lifts drawer top properly.

The ice maker was easy but the older Maytag inlet valves are rigid plastic line- make sure that line is properly connected to back of fridge- the 1st night the water leaked down back of freeze- thus no ice in ice maker tray ----but the bottom of freezer was full of frozen water--- took ice maker off and realigned inlet pipe- once that was done- no more problems- ( did also have to take hair dryer and remove all ice build up in bottom of freezer --- remember to check that rigid line as it can become detached while changing out ice maker assembly- thx Greg

This was a very simple repair. It took longer to remove the crisper bins than it did to repair the pantry end cap.

Sorry for delay in writing. Part I ordered arrived two days ago and it was exactly what I needed. Knowing that there will be problems even with the smallest job I procrastinated starting. When I did start this morning I foud I had to completely remove the ice maker and disassemble it in order to install the water fill cup bracket. The challenge was reassembling the unit. Not hard for an experienced repairman but a challenge for layman. Everything is thing is back to gether now and power on cooling down the refrigerator. Won't know how successful it was until turn on water and ice is formed. If it works this saved $75 just to get a Sears repairman to come out and tell me what would be needed to fix the refrigerator and $1,000 if I had to buy a new refrigerator. Extremely satisfied with service I received. Thank you.

I fortunately found the Part Select web site!! Used the trouble shooting guides and diagrams to diagnose the likely problem. Viewed the installation videos provided on the site and followed the procedure to complete the repair in about 15 minutes. It was a snap (actually three snaps) Fridge now working like new!! Thanks for the great information, guidance, pricing and superfast delivery!! Ron

removed drawers and glass; removed screws from end cap. removed screws from metal drawer runner. popped end cap off. reinstalled new end cap; attached metal drawer runner; cleaned everything and put glass back in as well as drawers. sweet

Thought I needed a new filter. Did not solve the problem. I returned the filter to partselect as per instructions. Will order from partselect when I need parts.

Followed instructions from a website called Anyone Can Fix It (cost $20 but was worth it). Part works perfectly. Saved a lot of money.

Lift drawer off sliders. Remove two screws holding drawer slider. Remove two screws holding left side pantry end cap. Screw new end cap into place. Screw draw slide into place. Replace drawer. It was a quick repair and finding the replacement part was real easy since the right side end cap needed replacing last year for the same problem. Weak design, but that's another story.

I lost the instructions so took one piece at a time off and put it on the new part. Then mounted it in the refrigrator. Works better than when it was new. Thanks for very quick shipping.