Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 59673503200 > Instructions

59673503200 Kenmore Refrigerator - Instructions

All installation instructions for 59673503200 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 59673503200
766-780 of 870
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Switch was not working after a repairman had fixed something else

  • Customer: Jackie from Nova, OH
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Please bear in mind I am 65 years old & it was harder to get up & down off the floor then to change the switch. Was very easy - watched video, unplugged unit. I used the putty knife at the right front corner to work loose, when it came loose had to loose the left side a little. The unit pulled out easily. detached the wired that had a single plug with 2 prongs on it. Attached the plug, pushed new switch into place. There was no way you could place wires on wrong prong. When done, plugged refrigerator back in & checked if working. I CAN SEE THE LIGHT and the food in the freezer now. Thank you for making an easy repair.

Broken lower drawer lid hinge

  • Customer: Chris from Amherst, MA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Removed drawers from fridge, removed screws/bolts from end cap, removed end cap with busted hinge pin,installed new end cap with lid , replaced drawers

not making ice

  • Customer: charles from lima, OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Move refrigerated and turn off water and unplug elect. Remove ice Ben and guide on right side. Move one screw on the bottom and lousen tow screws on top. Remove ice maker to unhook electrical connection. Transfer parts from old one to the new one . Revise the removal of it and when done .Plug in cord and turn on water. If you have done everything very carefully you will have ice in a few hours.Good luck.

Like many others, the tab broke off that held the drawer in place.

  • Customer: Jerry from Odessa, TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I took out the two shelves that were in the way. Lifted the glass out and set it aside. Since the pantry drawer cover wasn't in, because the tab was broke, I lifted the support beam out, pulled out the drawer and lifted it out. (The pantry drawer just lifts right out, straight up then towards you) I took out the back support beam, it lifts straight up. After that, I used a screw driver to take the pantry drawer glider (part #12) off of the broken one, then I put it on the new one so I wouldn't forget its orientation to the new part. I used a my socket set to take out two (should be three, but mine had two) bolts. I then gently pulled off the part needing replaced, first pulling it to the left, bringing the SLIDE- TEM (part #11) the BAR- TEMP (part #15) with it. Part #11 is held in by a tab at the back, to the left, so when you have the whole thing at the correct angle, it just slides out. (Pulling to the right, when you have the whole piece angled towards the center of the fridge, to the left.) After you get that piece out, you'll be able to clean the bottom of the fridge, it's amazing how much crap builds up on the bottom! (I even found a dead fly, eww! LOL) Taking parts #11 & #15 off of your old piece is easy, two tabs that you bend in on the right side of part #11 loosens it from your old part, then twisting it to take the pieces apart then lifting a few tabs to get #15 off of the old part. Then twisting it again to get the KNOB-TEMP (part #14) off. Pay attention to how you take this apart! It goes back together just like it came off! Attach these pieces to your new piece then it slides right in like you took it out. Slide the back left of #11 into the tab, reinsert the bolts, put your support bars back in, put your drawer in, put the drawer cover back into the new tab you just installed, put your glass in and finally, your shelves. All done!

The icemaker was leaking into the ice hopper creating an iceberg.

  • Customer: Peter from Hemet, CA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
After receiving the new ice maker assembly I placed the new part next to the old one to see what I needed to transfer from the old to the new. After removing the wiring harness and a few small parts, I placed them on the new assembly. After that it was a snap which timewise took about 15 minutes. I am pleased to say the ice hopper is full and being replenished very efficiently.

Replaced icemaker

  • Customer: Howard from Houston, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
1. Prepare the new ice maker by installing the bail cut off from old unit and installing the wiring harness from old ice maker. 2. Turn off the freezer unit only and turn off water supply. 3. Unplugged the electrical connector from the ice maker to the plug in back of freezer compartment. Remove the three (3) screws holding ice maker in place. Placed the cap from old unit to new ice maker. 4. Plug the electrical connector to the plug in back of freezer. Attached new unit with the three screws. Place bail in on position and turn the freezer and water on, ice made in circa 3 hours (without leaking I might add :)

no ice

  • Customer: Robert from Mondovi, WI
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Easy

Light on refrigerator went on to replace filter

  • Customer: CAROL M from TUCSON, AZ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Just replaced a water/ice filter..

Broken Water Nozzle at Door

  • Customer: Chris from Brentwood, TN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
(1) Ordered PS371704 from PartSelect! Best advice EVER! (2) Unplugged refrigerator (since the water solenoid on the back of the refrigerator is powered to switch ON the water, you NEVER have to turn off the water!) (3) Pull off the refrigerator's bottom grill. (4) With a small saucer under the fittings, unscrew the black and white tube fitting. There is only one nut to remove on the white tubing side. You'll need to undo the compression fitting on the black tubing and slide off the compression nut. You'll need to MAKE SURE you keep these nuts and replace onto the black and white tubing the SAME WAY you took them off. You'll NOT need to use nut drivers as finger tight is the key. Too hard and you'll ruin these plastic nuts. You should get only about 1/8 cup or less of water during this whole exercise. (5) Cut off the old, broken water nozzle. (4) Find a screw of the appropriate size to fit tightly 1/2 way inside the new tubing (this is to ensure your old and new tubing are connected to feed through the door). If screw is not tight within the tubing, wrap part of a plastic (thin) sack around this screw a couple of times and force into the tubing. You'll, of course, then need to use the hacksaw to cut the head off the screw as you'll be forcing the other half of the screw into the old cut tubing (6) Chase the dog out of the kitchen and cajole your wife (significant other) to push the newly joined tubes through the top of the dispenser, through the door and out the bottom as you will be gently PULLING on this old tubing from the bottom until the new tubing pops through the doors bottom. (7) Once this new tubing is out, you will separate the old tubing and, using the nuts in the proper sequence, connect this new tubing to the white tubing. (8) Plug the refrigerator back in and test flow the water. Check to ensure the plastic nuts have no leakage ... button up the bottom grill ... and enjoy the fresh water! PS> Don't forget to praise the wife (significant other) and give the dog a treat for staying out of your face!!

Drawer slide had a busted hinge pin

  • Customer: Stephen from Cottonwood, AZ
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
removed the two drawers. due to the refigerator location, had to remove the door. Then it was just 3 screws and put in the new end cap and then replace drawers and door. Job is done in less than 20 min and the wife is happy again.

Installed new Ice Maker

  • Customer: James from Chatsworth, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Followed the instructions from the excellent video by Steve on your website which made the installation easy.

Loud, non-rythmic clicking noise shortly after the compressor comes on, continuing for several seconds.

  • Customer: PHILLIP from SUN CITY CENTER, FL
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Replaced the "Run Capacitor. The non-rythmic clicking associated with the compressor coming on continues. The problem was obviously not the Run Capacitor". I don't know what to do next. Any suggestion would be appreciated.

Thanks,

Phillip

Plastic clips that held in clear plexiglass broke off

  • Customer: Kenneth from Howell, NJ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Very easy to replace the old broken piece with the new one. Simple

left pin for deli cover brken

  • Customer: Paul from Tucson, AZ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
removed deli tray and produce drawers.removed three screws with nut driver;removed track;trannfered track;reinstalled lefgt end cap.

Filter needed changing

  • Customer: Lynn from Rome, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Simple! Pop the case open. Counterclockwise to remove old filter. Wipe out excess water. Unwrap new filter; remove tab. Place in filter holder; turn clockwise. Close case. Run water to remove air. Couldn't have been easier!
All Instructions for the 59673503200
766-780 of 870