Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 59673503200 > Instructions

59673503200 Kenmore Refrigerator - Instructions

All installation instructions for 59673503200 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 59673503200
736-750 of 870
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Not making ice

  • Customer: Dean from WYOMING, MI
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
New part arrived in 15 hours with regular shipping. Watched your video and had old one out and new one in, in 20 min and ice in an hour more. Fantastic!!!

Original ice maker was leaking from a cracked tray

  • Customer: dean from holmdel, NJ
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
It is a simple and quick repair especially if one is even a little capable. May take some extra care and thinking for one who is not but still should be fairly quick and without troubles. I am not happy with the product as it does not make ice even half as quickly as the original. Many have stated the first or the first few cycles are very long and then it became quicker and more normal. Its been a week and I also tried shut it off several times just to reset it. It makes ice wonderfully but takes forever. I've yet to have a full bin of ice. Even without using ice for a couple days or very little in a few days. I am considering returning it for this reason.

inop ice maker

  • Customer: john from lakewood, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed ice rack and ice maker. installed and tested new unit.

left side pin broken on pantry end cap

  • Customer: Terry from Anaconda, MT
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed all plastic drawers and glass shelf. removed two screws holding the part to the side. Removed the slider metal part and placed it on the new part. Reversed the process, project complete.

Ice maker was dripping and creating a giant ice block

  • Customer: Sharon from Saint Augustine, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I never would have imagined that my husband and I could replace our ice maker so easily. We simply fired up the step-by-step video on my tablet, paused it as we did each step and voila! Usually there is a lot of cussing with any repair we do and I don't think there was even one cuss word uttered. Thank you for the clear and concise instructions!

Evaporator coils frozen solid / refrigerator not cooling

  • Customer: Richard from Cascade, CO
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Required about 20 minutes with hair dryer to melt ice from coils. Ohmed out heater at 30 ohms. Noted (as others have) that defrost thermostat was bulged out on one end. Reassembled and ordered replacement thermostat. Received part in three days. Kit contained all parts required for replacement - wires were color coded for easy replacement. Cut both brown and orange wires and used supplied crimp connectors to splice in new thermostat (will need crimpers). Reassembled unit. Actual time to replace part was about 15 minutes. Plastic grill has indications on both sides where to insert a screwdriver to release tabs holding it in place (there is also a tab in the center which is not marked).

Broken plastic dowel

  • Customer: Jerry from LA, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I unscrewed three screws and took off broken side. Then I unscrewed three screws and removed and replaced drawer slider. I then replaced old side with the new one.Thanks you for making this so easy.

The ice maker stopped working and left "kling-ons" in the tray. At one time the trays kept trying to fill which only sent water pouring into the freezer compartment.

  • Customer: Patrick from Fairfax, VA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Searching Google and Youtube produced trouble-shooting guidance to first check the water inlet valve which I did. I should have realized the valve was working since the ice-maker was trying to fill the trays. Additional advice recommended skipping all the other component troubleshooting and merely replace the old unit which I did. The big difference with the Amana appliance was the icemaker was installed laterally in the back of the freezer rather than longitudinally with the end of the control wheel positioned towards the front of the freezer. This created a tight fit in removing the old unit, especially since the wiring harness was extremely short. The latter made access to the plug release catch difficult. I used a small flat blade screwdriver and worked mainly by feel to release the plug catch. Persistent wrangling finally got the plug detached and the unit free. The water inlet hose also had a rear access orientation while the replacement unit had access was from the side. The hacksaw blade was used to cut a pre-outlined access to allow the hose to enter from the rear as with the old unit. Once the shut-off bail was transferred, wiring harness reconnected, and water inlet positioned and clipped into place, the mounting screws were secured. Within 24 hrs the first ice cubes popped and the unit has filled the ice reservoir. Keep in mind I just ordered the icemaker and did not need any other add-ons like a different wiring harness which seemed to work fine. Confirm when you order you don't need any additional parts. Good service for PartSelect. I will use them again.

Ice maker started spilling water and then stopped making ice

  • Customer: Daniel from Chicago, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
1. Watch the video. 2. Save your old ice maker's cover, metal lift bar, and power cord and clip. New one does not come with the cover, metal lift bar and power cord and power cord clip 3. My ice maker had three screw. two on top that only need to be loosened. on e on the bottom that has to be removed

The little part that fits into the hole of the deli tray door broke apart from the panel on the right side of the refrigerator.

  • Customer: Miranda from Kansas City, MO
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
There are two screws that holds the panel on. I took the screws out pulled the panel and attachments out. Removed the attachments from the old panel put them on the new panel. It was really easy to figure out how to fit the pieces back together. Screwed the panel and attachments back into to place and perfect. I Put the door back on the deli tray. No readjusting was necessary at all good as new fits great no problems. You pull the tray out the door flips up every thing works fine.

Refrigerator stopped cooling compressor did not cycle

  • Customer: james from indian springs, AL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
unplug power! Remove the screws from lower panel on back of refrigerator. Lift wire mount out of back panel. Capacitor is mounted directly to the relay and overload switch located on the left side of the compressor. Remove the spring clip holding the capacitor in place and pull the old capacitor out. Plug in new capacitor and replace spring clip. Use vacuum to remove dust from drip pan and wipe fan blades clean. Replace wire into slot on back panel and replace screws. Remove front coil cover below freezer door. vacuum dust off coils and replace cover. Plug refrigerator in and enjoy cold beverages. Relay and overload kit were not required for this repair.

Hinge On Deli Drawer Broke

  • Customer: Marilyn from Venice, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
As others have described. Went very smoothly

broke tab off hinge on left side..have had for 4 yrs

  • Customer: Bill from Denver, CO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Nutdriver....removed crispers.......pulled drawer. While drawer slide pulled out...removed 1 screw. Removed second screw. After looking at new on I understood had to pull up a bit while removing to clear taps at front and back.I am a handy kinda fella that fixes everything tho"

ice maker wasn't making ice

  • Customer: Sue from Mandeville, LA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
took off the old part and replaced with new using some parts from the old ice maker. We had to make one new screw hole because the new ice maker didn't match up with the old holes. Easy installation took 30min.

Ice maker was leaking and needed to be replaced

  • Customer: Rochelle from New City, NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I followed the instructions shown on the YouTube video on the Parts Select site. I had to make a few modifications. There were two nuts that had to be loosened to lift the ice maker off the freezer wall. The mounting bracket had to be transferred from the old icemaker to the new one to align with the hole in the freezer to reattach. The white wire went under the clip was a black wire but it was easily recognized. Other than that it was very straight forward and I had new ice in a few hours. I would definitely do it again.
All Instructions for the 59673503200
736-750 of 870