59673503200 Kenmore Refrigerator - Instructions

So easy! IDed the part with ease with the pictures.When the new part arrived, removed 2 screws from the old part and 2 nuts.Then removed old part and replaced with new part, which fit perfectly.Replaced screws and nuts, put the drawer and lid back on and done! I am a not very handy 58 year old female and this was easy.

Removed the 2 veggie drawer, removed the meat /pantry drawer and shelf. unscrewed the screws, removed the end cap and replaced it with new end cap - screwed the screws back in and voila - DONE!

Removed the 2 bins, glass shelf, large drawer. Removed the 2 screws holding the right drawer slide. Removed the 2 screws holding the pantry end cap in place. Transfered all the parts from the old end cap to the new end cap and reinstalled the end cap. Replaced the slide, glass shelf and the drawers. Installed the large drawer cover (very carefully!) as this is what broke off last time. Total time start to finish about 30 minutes.

Empty out freezer loosen two top screws and took out bottom screw. Lifted out ice maker and unplugged wire. Took bailing arm and plug and put on new ice maker and reverse the process. Had ice in three hours and no leaks.

Was very easy after I found right tool to get out the screws. There were only 3 popped old one out and put new one in. I waited over a year thinking this was a difficult/expensive repair. So not true...22$ and 15 min. I will definitely recommend this store/site and maintain it for my future use.

Removed wiring from old ice maker and install on new. With 2 screws all ready in place hung ice maker on them. Attach wire connector into socket and install bottom screw to hold ice maker. Tighten top 2 screw and put wire guide in place. Drop wire guide down and ice started in 10 mins

Pretty easy repair, the hardest part was probably putting the back back on. Once the back was off it was a matter of unplugging the Relay Overload and Run capacitor from the compressor. Taking the new parts snapped them together plugged it back into the compressor and plugged it in. The fan came on the fridge started working and everything is working fine. Parts came in on time and will definitely order again from Part Select again when I need to.

had to replace side cap s because plastic pin sheared off

I first reviewed the video, paying attend to the order in which items were removed and put back in place. On the video, I noticed that the lid to the draw was put back into place before the draw. Following these instructions, the repair went extremely easy and fast. I would recommend reviewing the video first.

Replaced the ice maker. I have a 3 door refrig. It has a bottom drawer freezer. Remove the freezer door to make this much simpler. On my unit, the ice maker is installed with three screws, rather than one and two clips. Check before you try to pull it out. You should unplug the old ice maker from the refrig, leaving the wires on the old ice maker. It's much easier to remove the old wiring harness from the old ice maker once you've removed the front plastic cover on the unit. Both plugs on the harness have clips on them to prevent accidental disconnections. Be sure to find and press the clip releases before you pull on the wires. Nut driver makes this job easier than screw driver. You only need one size for all screws. I used the old ice maker bottom mounting clip rather than trying to bend the new one to shape. Much easier. My old ice maker had an extra wiring clip, which I moved to the new unit before the install. There is one wiring clip to hold the temperature probe, and another just to keep the wires neat. Letting the old ice maker front plastic cover warm up a bit before you try to pry it off for reuse is a good idea. Less chance of cracking. Two hours after the install, I had new ice in the ice bin.

Remove the vegetable and fruit drawers. Cover of the pantry was off due to the broken pin. Remove the three nuts with a nut driver. Lift up on the old end cap to remove and replace it with the new one. Replace the nuts and put the cover back on. Replace the two drawers and you are done. Repair was easy

Opened the refrigerator door, pulled down the filter cover, twisted the old one out and removed it. Placed the new one in - twisted it into place, replaced the cover and closed the door. It is working great!!

Your video was very helpful and accurate. However, my freezer is a bottom drawer type, so I needed to remove the freezer door first. There were 4 nutscrews which needed to be loosened, and door lifted off. Now with the door off, and both baskets removed, access to the ice maker was easy like your video. Also, the freezer compartment was much more accessible for cleaning as well. In 2 days after replacing the ice maker, we have had 2 full batches of ice, with full sized cubes! Your ecommerce shopping, delivery, and instructional videos made for a great on line buying and installation experience. Note: The Dacor ice maker was replaced with a Whirlpool ice maker part. Your replacement part was identical in all respects to the original equipment even though Dacor was not included in your list of compatible brands.

watched the video you have on installation and followed it with ease. The only part you need a tool is to loosen the first nut and then everything else pretty much pops out and you reinstall with the new part. The icemaker worked within an hour and makes perfect cubes. The videos are super helpful.

Take filter out of the box and open the refrigerator. Open the housing in the frig that holds the filter and twist the light-blue piece 1/4 turn, counter-clockwise. (Put the light-blue piece in a safe place.) Take foil away from filter. With 1/4 turn in the clockwise direction, twist the filter into its position. Let five gallons run through the system to get fresh, filtered water.