59673502201 Kenmore Refrigerator - Instructions

I have never before seen a bulb with the filament intact not light. If the bulb's filament seems intact, screw the bulb into a known working lamp and see if it lights. When screwing it back into the socket in the fridge, it takes a bit of extra effort to fully seat (until it does, it won't light!). For replacing the switch, I unplugged the unit, used a paint scraper and worked it under the switch bezel from the right side. A bit of moxie, and the switch came out. The replacement switch had a different spade contact spacing than the original. I used a pair of scissors to cut the rubber bridge between the two switch wire connectors so I could connect to the new switch. In the end, it turned out to be the bulb. NOTE: The Model TC18KL is _not_ listed! What I finally found that the number "P7803211WL" on the sticker is actually a manufacturing code. Found this out by searching, and Sears' part search came up with matches.

self installled

Snapped the old one out and the new one in place. Only took about one minute.

Removed stuff in bottom of fridge removed two hex head screws removed drawer slides reassembled in reverse order put stuff back in fridge Bought from Parts select because their graphics for identification of part needed much better then others

Replaced the part, I'm a former appliance service business owner but if you have a small bit of mechanical ability you can change this yourself. Be Careful though internl workings seem flimsy and you might break another part that might ruin your day.

The part came in 5 days from time order. take less then 10 minute done. part work well, have ices again, Thank you Part Select. we don't have to buy a new Rerigerator

Removed pantry slide out drawer, removed both upper drawers, removed glass shelf (below 2 drawers). Removed the front glass shelf support. It just sits in a grove, comes right off.Used a ratcheting screw driver,with no tip, to remove the screws holding the end cap. Disconnected the air flow adjusting lever from end cap.Cleaned the whole area with a sponge and soap and water.lol.( amazing how dirty it can get being out of sight). reinstalled the lever on the new end cap, screwed it in place, put everything back together, DONE!It took about 20 min, including cleaning.Oh yeah, had an "inservice" with my grandaughter on how to close the 'fridge door.

I started by changing the water inlet valve. It made one batch but it did not eject into the ben. I removed the ice maker and found that the coating inside was bad. I changed out the ice maker and it is now making lots of ice.

I turned the water supply off and installed the new filter, which was easy. the hard part was finding the water filter at my local home improvement stores; they don't carry it. In the future I will use only Part Select.

Relaced the defrost heating coil and defrost thermostat. Works great. Just wanted to mention the lady I talked to from cutomer service was wonderful, sorry I don't remember her name, but very helpful. Thank you.

PartsSelect makes it so easy. I love that they inlcude a picture of each part so I am sure I am buying the right thing!

I went on line and viewed the video. It looked so easy I ordered the new ice maker. Having the information I was able to take apart the old one and view the problem. By the time the new part arrived I was experienced with the installation. I was shocked when the new ice maker arrived within 1 day. I completed the installation without a hitch, I was delighted with the ease of installation and the operation of the new iace maker.Thanks again...Ray

This was sooo easy! Removed the vegetable bins and shelf. Then removed the the deli drawer and lid. Used a 1/4 inch nut driver to remove the three nuts. On kitchen counter, I removed the two cross-cut screws from slide rail and put it on the new piece. Replaced the three nuts on the new end cap and then the hard work began---clean the shelves and bins that had been removed and replace the food. My refrigerator looks like new!

went by instructions, used a little common sence.

Disengaged the hinges, removed old drawer lid. Engaged hinges on new drawer lid. Done