59673502201 Kenmore Refrigerator - Instructions

I watched the video on how to change the ice maker, very easily explained, and removed the old in about 10 minutes.After seeing how the old one came out it only took five minutes to install the new one. The appliance repaircompany wanted$120 just to diagnose the problem,i bought the part from partselect for$104 total. This is the forth time I've used this site and saved a ton of money.

The annoying cover to the deli drawer broke off again. This is my second time purchasing this part from this website (left side and now, right side). Both purchases were very easy. Replacing the left side is easier because there isn't a temperature adjuster to remove and reinstall. I found this website very easy to find my parts both times, and I installed the right side (the latest fix) in less than 15 mintues while taking care of two kids. Many women do repairs around the house and are successful! :)

The repair is staightforward. Simply remove the deli drawer (up and out), the glass lid, and the vegatable drawers above it (easier access- they just slide out). Using a 1/4 socket I removed the 3 screws holding the end cap in place. You then disconnect the 2-3 places where the end cap connects to the humidity adjustment (front and rear). When the end cap is out you have to remove the drawer slide as and humidity adjustment slide as it isn't included in the replacement part- just 3 more screws- same size). Attach the drawer slide to the new end cap and do everything in reverse to replace it. Took all of 20 minutes including cleaning/drying the drawers etc while I had them out. Easy project.

Disconnected power--removed ice holder tray--removed ice maker end cap--disconnected electrical wires--removed one screw holding ice maker to refrigerator--lifted up on ice maker to remove it from two holders--took control wire from old icemaker and installed it on new one--reinstalled new icemaker in reverse order.

Replaced the water filter with the bypass plug. The water in western NC is perfect out of the faucet.

Rmoval and replacement is not at all complicated. (1)Reach behind and to the left of the icemaker and release the power plug. There is a release snap on th side of the plug. (2)Using a 1/4" nut driver remove the screw holding the icemaker to the "L" bracket at the bottom of the icemaker. (3)Using the nut driver loosen two self taping screws holding the top of the icemaker to the side of the freezer compartment.(4)Lift up on the icemaker to remove it. (5)remove the white plastic cover from the front of the icemaker (pry out at the bottom) and snap it onto the new icemaker. (6)Remove the wire sensor arm from the old icemaker and place it on the new one. (7) Remove the cable assembly (plug) from the old icemaker and fasten it to the new one. (8)Secure the new icemaker in place using the reverse order as the removal. The icemaker will take a little longer to make its first batch of ice as it will have to attain its proper operating temp (0 degrees to 2 degrees F).

I did some research online and found that others were having the same problem and I read how they fixed it. It truly was as easy as they wrote. I replaced the run capacitor and the relay overload with parts from "PartSelect". In the process I blew out the accumulation of dust on the bottom of fridge, and just like that, the freezer started freezing and no more noise. $106.00 repair vs. $1600.00 for a new one. My Whirlpool is now like new.

we only had mm sockets so had to go to the hardware store when we found they would not fit. We needed and american socket i/2 way between #6mm and #/7mm which turned out to be a 1/4 inch socket

I ordered the grill without listening to the advise given by the operator and ended up reordering the correct part. Ya just gotta listen to the people who know or else. But The order was filled in record time with absolute perfection and the instalation went fgast and easy. Now, my wife is a very happy camper... thanks to the very kind, helpfull and professional folks at PartSelect. Lamont.

I took all the food out and the shelves above the area. The end cap was a piece of cake to remove, only two screws to take out, and installing the new ones was very easy.The reason it took so much time is because I thoroughly cleaned the fridge at the same time.

Removed items from frifge, took out the lower drawer, removed side plate with broken part by nutdrive, replaced it, and put everything back - about 15 minutes. Easy.

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

Since I had more than one issue, I decided to replace the entire ice maker. All I needed was a nut driver and it took 5 minutes. Three hex screws and unplug the wire harness and the whole unit came out. I changed the harness over and installed the new unit. I left for work and came home to ICE. It was Great!!!

After one attempt to use super glue failed, obtained the part (shelf support). Had to remove drawers and a shelf to get to the support. Two hex screws held in place. No problems, a little touchy to put the lid back on, but all in all a simple repair. Didn't have instructions - didn't need them - it was straight forward.

Removed large lower drawer, removed contents from the lower shelf, removed the two produce drawers, removed glass shelf. At that point you will be able to remove the three screws from the left side pantry end cap. A slight upward and forward motion will release the side pantry end cap once the screws are removed. Once the side pantry end cap is removed, two screws will removed the drawer track. Note: you will have to slide the drawer track one way or the other to align a small hole to find and remove the hidden screws. The process was reversed to install the drawer track and side pantry end cap, etc. The actual removal and installation of the new side pantry end cap took less than 10 minutes. I was very pleased with the ease of ordering and speedy delivery of the part from PartSelect.com