Models > 59673502201 > Instructions

59673502201 Kenmore Freezer - Instructions

All installation instructions for 59673502201 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the freezer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 59673502201
796-810 of 847
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

ICEMAKER

  • Customer: BETTY from HOCKLEY TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I RECEIVED THE NEW ICEMAKER THE NEXT DAY AFTER I HAD ORDERED IT.AFTER WATCHING THE VIDEO ON HOW TO INSTALL THE ICEMAKER I INSTALLED IT WITHIN A FEW MINUTES WHICH I REALLY SURPRISED MYSELF SINCE THIS WAS MY FIRST REPAIR JOB TO DO BY MYSELF.THE NEW ICE MAKER HAS BEEN WORKING GREAT AND I AM VERY PLEASED WITH PARTSELECT AND WILL CONTINUE TO CONTACT YOU WHEN I AM IN NEED OF ANY PARTS. THANK YOU, BETTY

dripping and making globs of ice

  • Customer: Edward from Philadelphia PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
1 removed ice basket 2 remove cover over basket 3 unplug power cord 4 loosen top screws with 1/4 in nut driver (do not remove the completely) 5 remove lower mounting screw ( not necessary to remove basket rail) 6 remove ice maker from unit 7 remove bale from old unit 8 install bale on new unit 9 remove front cover from old unit 10 remove power cord from old unit 11 plug in cord to new unit 12 install old front cover on new unit 13 mount unit in freezer 14 hang unit on top screws 15 install bottom screw 16 plug in unit 17 put in ice basket and cover. no runs, no drips, no errors. Ice was made in about 2 hours.

Ice Maker stops working..

  • Customer: Tony from Litchfield Park AZ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Fast delivery...Great video instructions..The only difficulty is when I tried to take the cable out. It's kind of hard and far away from my reach. So, I took only the cable out on Ice Maker end.

Ice maker tray in side by side leaked and created large lumps of ice

  • Customer: Catherine from Punta Gorda FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Unplug refrigerator, turned off water to ice maker, unscrewed bracket, lifted ice maker off clips, pulled out water hose,disconected wiring harness and lifted out old icemaker. Reversed the process and it worked like a breeze and no service call. Space is very tight and you have to do a lot of feeling without actually seeing what you're doing and you need a small flashlight. It was so easy with diagram provided on PartSelect's website.

Stopped making ice, leaking water into freezer to kitchen floor!

  • Customer: John from Seabrook NH
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Found PartsSelect on internet. Read data, watched remove/replace video, ordered new Ice Marker. Arrived in 11/2 days-quick. Both removel and install very easy; three easy to remove screws, disconnect wire harness pull it out. However, water cup on end of the new Ice Maker was faceing 90 degrees the wrong way! Had to totally disassemble both new and old Ice Makers to swap water cups. Reassemble, pray it was done correctly and install. New Ice Maker works like a champ and no leaking--Thanks PartsSelect.

Ice maker stopped working. Turned out a connection on the heating bar shorted out.

  • Customer: Russ from Supply NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Pulled the plug on the refrig. ( This is important since the heating bar on the bottom of the ice maker could come on as soon as you plug it in and burn your hand ). Removed the ice bin to get it out of the way and then removed the 1/4" hex screw from the support bracket under the old ice maker ( don't lose it ). Pushed up on the old ice maker to dislodge it from the 2 support clips on the top of the ice maker. Squeezed both sides of the wire harness plug and pulled it out and removed the old ice maker. Removed the wire harness and level bar from the old ice maker and installed them on the new ice maker. Plugged the ice maker wire harness into the female receptacle in the freezer. Popped the ice maker in to the top support clips making sure the rubber water chute from the refrig. was in place in the round ice maker receptacle. Plugged bak in the refrig. and I was getting ice in about 2 hours. Working fine after 1 week producing plenty of ice. RussK---

ice maker stopped making ice

  • Customer: David from Jacksonville FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
following the advice of this site, purchased a new ice maker. Old one was simple to unhook and remove and new one was just as easy to install. Within no time at all, I had ice being made and it has been working perfect since. Thank you for the help...

Frost in bottom freezer, freezer 8%, ice maker works

  • Customer: Richard from Smyrna GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
replaced electric control board, defrost for six hours. next day (24 hours) same problem, dusterhoff2928@charter.net

My refrigerator light did not work.

  • Customer: Fred from Warwick RI
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
After years of using a flash light to check the contents of my refrigerator, I decided to try to fix the problem myself. Replacing the light switch was very easy. The directions were straight forward and I'm sorry I waited so long to tackle the problem.

refrigerator/freezer would not cool

  • Customer: James from Bedford NH
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Set the freezer control knob to OFF. Use a long bottle brush to clean the cooling fins below the freezer by removing the lower front grill. Pull fridge away from wall, unplug, remove rear panel near bottom, remove power connector to the unit attached to the large black tank(condenser). Be very careful not to damage the quick connect housing. There is a wire spring holding the capacitor/relay assembly to the condenser. The black run capacitor and the white overload relay come off together. CAUTION, THE CAPACITOR MAY STILL BE HOLDING A CHARGE. Don't separate the two items unless you are familiar with electrical safety precautions. Plug in the new items on the condenser, reconnect the power cord, plug in the fridge and turn it on using the freezer control knob. You should hear the condenser start. It is possible to remove the two parts and test them separately. My capacitor was fine but the relay had blown. I replaced both since it seems most problems are one or the other and it was easier to do them together. Cleaning the cooling coil and removing/replacing the back cover are the most time consuming parts of the procedure. The actual repair took 5 minutes once I had access.

Frige and freezer quit working

  • Customer: jamie from long beach CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Two days prior to realizing unit was not cooling I was hearing a clicking sound at the back. My google research told me a clicking sound indicates a problem with the "relay overload". If you remove this and it rattles when you shake it, that tells you it is bad. Mine rattled alot. To start, I unplugged the fridge. Removed the vented panel at the exterior lower rear. Removed the wire clip holding the "relay overload" in place. Unplugged the "relay overload" from the compressor. Note that the "run capacitor" is plugged in to the "relay overload" and they will appear as one unit. I replaced both w/new. I plugged the two together, plugged them into the compressor, plugged the frige in to test and it worked. Put the wire clip earlier removed back in place. Reinstall the vented panel. Push frige back into place.

Loud, non-rythmic clicking noise shortly after the compressor comes on, continuing for several seconds.

  • Customer: PHILLIP from SUN CITY CENTER FL
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Replaced the "Run Capacitor. The non-rythmic clicking associated with the compressor coming on continues. The problem was obviously not the Run Capacitor". I don't know what to do next. Any suggestion would be appreciated.

Thanks,

Phillip

broken water fill cup

  • Customer: augustine from cedar rapids IA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
empty frezzer take door off unplug wires going to ice maker unscrew/bolt icemaker replace door take motor cover off ice maker remove screws on motor replace ice cup and put every thing back together

Freezer section icing up, getting too cold, refrigerator getting too warm.

  • Customer: Cecil from Carmel Valley CA
  • Difficulty: Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Local appliance repair co. diagnosed and replaced motorized door in refrigerator section; problem manifested itself again one week later. Same appliance repair co. then said it was probably the defrost thermostat, they changed thermostat; problem came back after another week. I went on your site and figured that the next most likely thing was the defrost heater. I ordered one and it came the next day. I dismantled the various panels, sensor covers, air dams and removed and replaced the heater element. After watching the refrigeration cycle for a couple of days I saw that the problem appeared to be cured then I replaced the panel and sensor and fan covers and put the ice cream back in. That was a week ago, it seems to be ok now.

new maytag filter clogged twice in two weeks no ice or water

  • Customer: Jim from Gleason TN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Took out 2nd new filter $43.00 each that clogged in less than 2 weeks each and installed in 2 mins. this bypass and ice and waterr work perfect.Thank you, thank you for your exceptional service ordered part and it came next day without extra charge,great service.
All Instructions for the 59673502201
796-810 of 847