Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
No water to dish washer
After figuring out the problem wasn't the water inlet switch, I replaced the switch assembly for the water level float. Cut off supply water to dishwasher, removed the 2 screws holding switch assembly, and installed new switch. 15 minutes, very easy job.
Removed eight screws holding front panel to door; placed blanket below it beforehand based on tip read in another person’s post. Removed two screws holding switch in place and then transferred four wire connectors one at a time. Replaced latch assembly with two screws. Replaced front door panel by reinstalling eight previously removed screws then did a load of dishes.
I was impressed with the user friendly format of your web site. I was able to quickly look up the part I needed. It arrived much faster than I expected after my order was placed.
I have already recommended the site to a friend needing parts for a Gibson dishwasher.
Dishwasher was leaking at the lower left side of the door.
Probably the easiest repair job that you could encounter. I removed the old gasket from the door frame. Cut the new gasket to length and pushed it into the door frame.
Dishwasher would not start; no control lights illuminated.
Replaced door switch as follows: (1) turned off circuit breaker powering unit; (2)removed six screws holding front control panel cover to chasis and pulled cover out slightly to expose switch; (3) labelled four connectors on wires to switch with marking pen; (4) disconnected the four wires: (5) removed two screws holding switch to chasis; (6)installed new switch with the two screws; (7) reconnected the four wires; (8)replaced cover panel and (9) turned circuit breaker back on.
Unscrewed dishwasher from cabinet and pulled out about 1 foot. Took bottom plate off of dishwasher. Undid clamp on hose of discharge of inlet water valve and removed hose. Shut off water to water inlet valve and removed. Took wiring clip off of water inlet valve. Removed 2 screws holding water inlet valve in place. Installed new water inlet valve in reverse order.
The Parts finder was the big help. After that all that was needed was to loosen the clamps and replace the old hose with the new one A piece of cake. Slide the washer back into place and replace the screws that hold it to the counter. Out and back in, 30min. top end to complet the job
Turned off power to dishwasher.Used a screw driver to rermoved the outer top of door.Used star wrench to remove door latch.Repalced wire for wire on door latch.Reinstalled door latch with star wrench.Reinstalled outer top of door with screw driver.Turned power on.Tryed door lath.Operation is Ok.Ran dish washer.No leaks.Operation is OK.
The plastic door latch handle broke-off and fell into pieces.
Removed 6 screws, pulled the front cover forward, removed the old door latch, installed the new latch, replaced the screws, DONE! Took about 10 minutes. The new door latch works to open and close the door, and the dishwasher runs fine when the door is closed. However, the new door latch does not lock the door into place like the old one did. I didn't remove the screws and loor latch assembly again, but there must be a difference between the old part or the new part. And I noticed that the old part number and the part number of the replacement part are not the same, although the website indicated that it was the correct part for my model.
Soap dispenser wouldn't open until the very end of the cycle
I'm a stay-at-home mom of 3 kids, so I enlisted the help of my oldest son (5 years old) for this job while the 2 little ones were asleep! First we cut the power to the dishwasher, then we removed the 2 bottom screws on the stainless steel front and slid it off to expose the back of the dispenser. We removed the red and white wires from the left side of the dispenser, took out the 6 screws holding the dispenser in place, put in the new dispenser, hooked up the red and white wires (in the right order), and flipped the breaker back on! We ran a cycle to make sure it worked, and it did!! My husband was thrilled! He thought for sure we needed a new dishwasher! :o) Thank you, PartSelect!
Removing two screws on the inside of the door alows the outside panel to slide down and detach. The soap dispenser connects with six screws and two wires. Remove the dispenser through the inside of the door. Replace, reattach and reasseble in 15 minutes.
First I shut off the power to the dishwasher from the breaker panel. Then I removed the five screws holding the plastic top panel to the door (on the frigidaire, there is no need to remove the entire stainless steel door panel). I removed each of the four wires from the old latch (pulling the wires off required some "oomph") one by one and plugged them into the corresponding position on the new one. I did this so I would be sure to have them in the right place. I used a torx screwdriver to remove the two screws holding the old latch. I then replaced the old latch with the new one, replaced the top panel of the door, turned the breaker back on and everything was as good as new! The whole operation took maybe 20 minutes. It couldn't have been easier. The only surprises were how difficult it was to pull the wires off and the fact that the screws holding the latch were torx head.
In future, when I need parts, I will definitely use PartSelect. I have gotten parts from other sources, and this is the first place where, along with the part, you get all this advice from other DIY'ers. It's an absolutely brilliant idea and a lot of help.
the valve stuck closed - no water would enter the machine
remove vanity panel disconnect copper supply line from valve remove valve mounting screws rotate valve to access hose clamp loosen clamp and slide up rubber tubing about 2 inches pull hose off barbed fitting and remove old valve reverse order with new valve
I foloowed the others who repared the same item. I really appreciated their help and input. The only thing I would add is when they said that you only have to remove the bottom 2 screws on the inside of the dishwasher door they are absolutely correct. But don't look on the very bottom of the door like I did. They are on the inside of the door, facing inside. The bottom screw on each side. Thanks for all the help.
Remove and replace the door gasket. Removed the 6 phillips head screws holding the top panel cover. This gives access to the latch assembly. Remove the two screw holding the latch in place. I removed the four wires one at a time with needle nose pliers and plugged them on the right spade of the new latch assembly. This assures getting them in the correct position. I then mounted the latch with the two screws and installed the cover with the 6 screws. Job done, piece of cake.
I purchased a wonderful portable dishwasher at a garage sale for $20. The woman had just redecorated her kitchen and was selling the relatively new portable model. All it needed was a new caster and a faucet adapter. After ordering the parts, they arrived in a couple days, and after less than 5 minutes of installing them I had a "new" dishwasher that works like a champ! Thanks for making this so easy!