Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
old valve leaked
I will make a few additions to the other instructions, which are great and let me see that the job was doable. To the tools needed, add pipe tape. 1. Shut off water supply. 2. Removed inlet water hose where it connects to the valve assembly. (This was a pain on my machine—too little room for the wrench, you may have a better tool—but I did get it out, slowly.) 3. Removed the two bracket screws holding the assembly to the frame, and detached the electrical connection (Look for your red and blue wires on the connector, my red was to the top of the solenoid, and reattach with the same grounding) from the solenoid. (This step was a great bit of information; It allowed me to see that I could do the following steps with ease, That is, the unit dropped down where you could work on it.) 4. Removed the inlet hose adapter connection from old valve and installed into new valve. 5. Attached electrical connection to new valve solenoid. 6. Remounted assembly to the frame. 7. Re-attached the inlet water hose to the hose adapter connection on the valve. (I had to take off the L shaped connector at the bottom of the old valve and add it to the new valve. This was an extra step that required two bigger wrenches to hold the old assembly and unscrew the L joint. I just needed the extra leverage to get the old off and the new on. I am referring to the copper connection that connects to you water supply) (8) The new valve had a slightly different configuration than my old. The rack it sits on was about an inch or so longer. This meant that I had to readjust my copper pipe just a bit to match up when it was reassembled. No big deal, I had lots of pipe length to work with. Actually, moving the valve a bit further back made more room for the wrench to work—very happy about that. In addition, the hose attachment went from a left exit to a back exit. Doesn’t seem to matter. (9) Turned on the water, washed some dishes. (Took me about an hour, mostly because of the difficulty with the wrenches. Otherwise—piece of cake)
Electrolux part number PS1524955, lower spray arm.
Problem. Dishwasher was spraying water out the bottom of the door. The spray arm was damaged when the heat shield overheated, causing the shield to contact the heating element. This resulted in the spray arm melting, causing water to be sprayed out the small gap between the dishwasher door, and the dishwasher bottom pan.
Repair Lower spray arm is easy to remove. Release the arm clips at the center of the spray arm. When the clips are released, lift and remove damaged arm. Replacement arm is attached by pressing down on the center of the spray arm. The new unit has smaller heat shields so it will be less prone to overheating.
Thanks for the fast shipping. Part was recieved in a few days. For just a few dollars, the handwashing is over.
It would sometimes work, which led me to believe it was a switch. Looked on line and found the mail switch to go on was in the latch. I took it apart, 6 screws, wiggled the switch and it went on. So I found the door switch to be bad. It was very simple to change the switch.
After figuring out the problem wasn't the water inlet switch, I replaced the switch assembly for the water level float. Cut off supply water to dishwasher, removed the 2 screws holding switch assembly, and installed new switch. 15 minutes, very easy job.
Dishwasher was leaking at the lower left side of the door.
Probably the easiest repair job that you could encounter. I removed the old gasket from the door frame. Cut the new gasket to length and pushed it into the door frame.
The spray arm comes off into 3 parts but is really only supposed to be one. I removed the nut from the old assembly and attempted to place the new assembly on by hand. The new nut seemed to be slightly smaller than the original so it would not attach to the dishwasher. Using a kitchen knife, I removed the new nut from the arm unit and attached the new arm to the original nut and it went back on easily. The connection of the new arm to the new nut was 3 tabs that needed to be depressed with the knife and was a different conection method than the assembly that kept coming off in the wash cycle. The replacement part had a much better design than the original.
One of the springs was broken, The door would not open or close properly. There was also a leak coming from the front of the dishwasher.
I removed the dishwasher from the cabinet space (two screws) and manually replaced both springs. I replaced one spring first to see if there would be an improvement when the second new spring was installed. There was much better tension once the second new spring was added.That is why changing both springs is recommended. This was very easy. Changing the gasket was scary because I thought the the whole door would have to be taken apart. You know nothing ever goes back together the same. I feared that I would create an even bigger leak than what I had. Taken the door apart didnt work for me, so I just pulled the old gasket by hand and pressed in the new one. I made sure that it was seated correctly. Voila no leak. The dishwasher is running as good as new. I ordered these parts on Friday morning. They were on my door step Monday morning, I highly recommend ordering from this site.
Discovered upper wash arm had come off. It looked like it was repairable, but the bushing/clip holding the arm came off after one wash. Looked on line and reviewed part and saw it was a one piece assembly from photos. Removed old assembly by unscrewing from top of washer and screwed new assembly in place.
Removed the bottom panel on the unit (2 screws hold it on) and pulled the dishwasher out about 4"--after turning off electricity to the unit. Removed the broken spring and the old linkage and replaced them with the new parts. Pushed the diswasher back into place, and replaced the bottom panel. Turned on the electricity and the diswasher door is "good as new." This is quite simple to do; just takes patience.