4KSRS22QFW01 KitchenAid Refrigerator - Instructions

Removed outer cover. Removed control bracket which holds the water/ice dispenser paddles. Removed paddles from old/broken bracket, plastic pins were broken where the paddles hinge. Placed on new bracket placed screws and it was done. Very simple repair. Part cost less then $18.00 including shipping. Saved me mucho dollars!!!!

hardest part getting the putty knife in right place to pop off cover---found the plastic bracket was broken where the switch was held in place---- so ordered new switches and bracket ---- got the parts in 3 days--good service--easy job 2 do and saved lots of $$$$$$$$---

I watched your video and did just as he did. The video made it real easy and rather simple. It looked like it was going to be a mess until I watched the video.

Put in new frame we bought from you..........Your video was perfect for instruction on replacement.

I watched the short video at this website about replacing the bracket first. Then I replaced mine. Everything went smooth. No problems. Try it yourself.

Sorry for delay in writing. Part I ordered arrived two days ago and it was exactly what I needed. Knowing that there will be problems even with the smallest job I procrastinated starting. When I did start this morning I foud I had to completely remove the ice maker and disassemble it in order to install the water fill cup bracket. The challenge was reassembling the unit. Not hard for an experienced repairman but a challenge for layman. Everything is thing is back to gether now and power on cooling down the refrigerator. Won't know how successful it was until turn on water and ice is formed. If it works this saved $75 just to get a Sears repairman to come out and tell me what would be needed to fix the refrigerator and $1,000 if I had to buy a new refrigerator. Extremely satisfied with service I received. Thank you.

The roller on the crisper drawer shelf on my KitchenAid refrigerator broke off and it was not repairable. I ordered a crisper drawer shelf replacement with rollers which arrived promptly in a couple of days. I watched the PartSelect video and made the repair in less than 15 minutes without tools. It was the easiest repair that I have ever made. I have used PartSelect in the past and have always been pleased with their service.

Followed the video supplied with shipment info from parts select. Simile and a great way to help the diy person. I will reyurn as a customer as well as pass the word. Thanks jhg

With the new Ice Guide all I had to do was a use a small screw driver to help guide the tabs into place and I was finished!

Took augur off broken bend put augur in new bend took 10 min now I can have ice. shipping was super fast.

This is for the refrigerator, not the freezer door which is more complicated. First empty the refrigerator door of food and removed the shelves. Remove the hinge cover on the top hinge by removing one bolt. Then, holding the door, remove the top hinge by removing the three bolts in the bracket (not the bolt in the recessed hole). Lift the door off the lower hinge and lay the door on its edge on the floor. Pry the old Door Cam out of the hole in the door with a knife (my Door Cam was ground completely flat). Insert the new Door Cam. Remove the old Lower Door Cam from the lower hinge and insert the new Lower Door Cam. Pick up the door and lower the door onto the lower hinge ensuring the lower hinge pin inserts into the hole in the Door Cam on the door. Reinstall the upper hinge and insert bolts without tightening. Align door and then tighten hinge bolts. Reattach top hinge cover and tighten the single bolt. Test the door to ensure it closes and stays closed. I had to remove the door a second time to rotate the Door Cam slightly to ensure cams were better engaged (tongue in groove style) when the door was closed. Reinstall the shelves and load the door with food.

Removed (snap on)removed screw, and ice dispencer side (door and Pin) You have to assemble to reinstall (not easy to install while assembled) Install the pivot pin the rest of the way with the new spring mounted and when unit is almost in place, install the pivot the rest of the way, install tension hold downs that old both the water and ice dispenser shafts, reinstall cover, reconnect wiring and test, I had to remove the plunger because the water wouldn't shut off fast enough. Unit works great now.

Replace the auger drum. I had order it and the auger, but I did not need the auger. I returned the auger with ease. Parts Select will always have my business.

The plastic control bracket would not "lock" in place because the plastic detentes broke, not allowing the ice maker dispensing 'paddle' to engage the micro switches that allows the ice maker to eject ice. An easy repair of replacing the entire plastic control bracket.

After our four year old refrigerator door wouldn't stay closed as a do it yourself kinda gal I found this website that assisted me in an easy and inexpensive fix. The "plastic" yes, "plastic" piece on the bottom of the door was worn down to nothing. My only suggestion is to call in your order, the customer service folks will help you order the right cam for your model. The next thing is to change both cams if you have a side by side. We changed the fridge side which fixed the problem, then realized the cam on the freezer needed to be changed to make it level. Great customer service!